User manual AEG-ELECTROLUX LAVAMAT 802T

[. . . ] The information marked with this symbol provides additional instructions and practical tips on the use of the appliance. Tips and information about economical and ecological use of the machine are marked with the clover symbol. If you require assistance or advice on your appliance, please contact our customer care department by letter or telephone: Customer Care Department AEG Domestic Appliances Limited P. O. Box 47 Newbury Berkshire RG14 5XL Tel: 01635 572700 Fax: 01635 42970 Printed on recycled paper. [. . . ] The pilot light corresponding to the wash phase which is running comes on. After about 30 seconds the programme starts. START PAUSE 26 How to wash At the end of the programme The machine stops automatically and three flashing zeros are displayed. The END and spin speed pilot lights, as well as the pilot light(s) corresponding to the selected option(s), stay on. If the RINSE HOLD option has been selected, the corresponding pilot light on the programme progress display flashes to indicate that the water must be emptied out before opening the door. The pilot light of the START button flashes and tree flashing zeros are displayed. Release of the lock is indicated by an audible signal. Switch the machine off by pressing the ON/OFF button. Turn the programme selector dial to RESET. Check that the drum is empty so as to avoid a subsequent wash being damaged by any forgotten items. Leave the door open to prevent the formation of mildew and unpleasant smells. 27 Programme chart Wash programmes Wash Temp. programme Fabrics Additional functions Max. Detergent can also accumulate inside the drawer recess: clean it with an old toothbrush. Refit the drawer after cleaning. 30 Cleaning and maintenance Drain filter The drain filter collects threads and small objects inadvertently left in the laundry. Check regularly that the filter is clean. Place a container under the filter and unscrew it; some water will come out of the filter. Clean the filter under a running tap, then refit it, screwing it fully in. Water inlet filter If you notice that the machine is taking longer to fill, check that the filter in the water inlet hose is not blocked. Unscrew the hose from the tap and remove the filter. Refit the filter and screw the hose back onto the tap. 31 Cleaning and maintenance Emergency emptying out If the water is not discharged (pump is blocked, filter or drain hose are clogged), proceed as follows to empty out the machine: · pull out the plug from the power socket; · close the water tap; · if necessary, wait until the water has cooled; · place a bowl on the floor; · put the drain hose end into the bowl and let the water out. Should it not be possible to have access to the drain hose because, for example the appliance is built in the kitchen furniture, slightly loosen the drain filter after placing a bowl on the floor to let the water come out slowly. At the end screw the filter again. Frost precautions If the machine is installed in a place where the temperature could drop below 0°C, proceed as follows: · Close the water tap and unscrew the water inlet hose from the tap. · Place the end of the drain hose and the inlet hose in a bowl placed on the floor. · Select the "PUMP OUT" programme and run it until the machine stops. [. . . ] This operation has only to be performed by a qualified electrician. 13 AMP 49 Building-in This appliance has been designed to be built into the kitchen furniture. The recess should have the dimensions shown in picture A. 176, 5 818 416 600 600 515 596 570 m in. 120 541 8 90 0 49 Preparation and assembly of the door The machine is originally prearranged for the assembly of a door opening from right to left. In this case it is sufficient to screw in the hinges (1) and the countermagnet (6) provided with the appliance, at the right level (Fig. B). 6 4 1 165 A 1 2 7 3 160 5 a) Door The dimensions of the door should 23 8 B be: - width 595-598 mm - thickness 16-22 mm The height (C-Fig. [. . . ]