User manual AEG-ELECTROLUX REGINA1850

[. . . ] ÖKO-LAVAMAT REGINA 1850 update The environmentally friendly washing machine User information Dear customer, Please read these user information carefully. Pay particular attention to the section "Safety information" on the first few pages. Please retain this user information for later reference. Pass them on to possible new owners of the appliance. 1 3 2 The following symbols are used in the text: Safety instructions Warning: Information concerning your personal safety. [. . . ] 30 seconds after the washing machine is switched on or after a button or the control knob was last actuated, the START indicator will begin to flash. If you do not wish to make any further settings, press the START button. If a delayed start has been set: If the DELAY START option has been selected, the wash programme will finish at the time shown in the display. If the wash programme has not yet been started, you can still cancel the delay start. The wash programme will start immediately. (See chapter "Setting options, e. g. DELAY START". ) If you would like to add washing even after the programme has started. Press the UNLOCK DOOR DELICATES 30°C 1000 RPM 11:25-14:36 button. main wash, and a bar showing the programme progress. The N symbol is displayed as the programme progresses: the loading door is locked. 1000 RPM PAUSE DELICATES 30°C 11:25-12:36 N§ MAIN WASH #####=========] 1000 MOISTURE 49 % Moisture/Loading During the wash programme LINEN/EASY-C. 60°C 1400 RPM 11:25-12:36 the display additionally indiN§ PAUSE cates: MAIN WASH ­ the expected residual #####=========] moisture in the washing at LOADING 80 % 1400 MOISTURE 50 % the end of the programme. The value depends on the selected spin speed. ­ the loading of the drum (in 10 per cent steps. ) This value is indicated with the LINEN/EASY-CARES and COTTONS programme only. The loading can be estimated by the washing machine about fifteen minutes into the programme. Changing the spin speed The spin speed can still be changed and rinse hold still be set during the programme. Cancelling the programme To cancel the programme before it has finished, switch off the appliance (press the control knob). The wash programme can be interrupted at any time by pressing the PAUSE button. 3 32 When the wash programme is complete 3 3 When a wash programme is complete, PLEASE TAKE OUT THE CLOTHES will appear in the display. If you do not press any buttons or press the control knob within three minutes of the programme finishing, the washing machine will switch into standby mode. The stand-by mode is cancelled by pressing one of the buttons or turning the knob. If EASY IRON has been selected, a crease prevention cycle of approx. 30 minutes takes place after the programme has ended. You can remove the washing at any time during the crease prevention cycle. To do this, press the PAUSE button and the door can be opened. For rinse hold If the wash cycle was ended with a rinse hold, the water must first be drained and if necessary the washing spun: Spin: 1. [. . . ] 61 Technical data Adjustment possibility Approx. +10 / -5mm Filling quantity (program-dependent)max. 5kg Area of use Domestic Drum speed, spinning See rating plate Water pressure 1-10 bar (= 10 - 100 N/cm2 = 0. 1 - 1. 0 Mpa) Dimensions (dimensions in mm) 62 Customer Services Schweiz - Suisse - Svizzera A + T Hausgeräte AG Kundendienst AEG Industriestraße 10 5506 Mägenwil Service Eine Tel. -Nr. für die ganze Schweiz ServicePhon 0848 848 348 Fax 062/889 95 85 Ersatzteildienst Ersatzteilverkauf ganze Schweiz Telefon 0848 848 028 Fax 062/889 94 90 Regionalbüro Westschweiz: 1028 Préverenges Le Trési 6, Verkauf Tel. [. . . ]