User manual AEG-ELECTROLUX MOD ETN1281V

[. . . ] We promise that it will provide a superior User Experience delivering Ease-of-Mind. Good luck! 4 electrolux contents Contents Safety instructions Description of the Appliance Operating the appliance Tips on Cooking and Frying Cleaning and Care What to do if . . . Disposal Installation Instructions Assembly Guarantee/Customer Service Service 5 7 10 19 22 24 26 27 28 32 34 The following symbols are used in this user information: 1 3 2 z Warning!Important advice for the safety of persons and information on avoiding damage to the appliance General information and advice Information on environmental protection Dangerous voltage safety instructions electrolux 5 Safety instructions Please comply with these instructions. [. . . ] Control panel Switch on Switch off Touch Touch Display (for 5 seconds) previously set heat setting When you switch the appliance off, the locking function is automatically switched off. 12 electrolux operating the appliance Using the automatic warm-up function All cooking zones are equpped with an automatic warm up function When setting a heat setting using , when starting from , the cooking zone switches to full power for a certain amount of time and then automatically switches back to the heat setting set. Control panel Switch on (only when starting at ) Switch off Not used Touch possible heat Display settings to (after 5 seconds) Touch Touch to to / to to If during the automatic warm up a higher heat setting is selected, e. g. from to , the automatic warm up is adjusted. If there is still residual heat on the cooking zone (display ), the automatic warm up is not performed. operating the appliance electrolux 13 The length of time that the automatic warm up function operates depends on the heat setting selected. Heat setting v 1 2 3 4 5 6 7 8 9 Length of the automatic warm up [min:sec] 0:30 1:00 1:40 4:50 6:30 10:10 2:00 3:30 4:30 --- 14 electrolux operating the appliance Using the child safety device The child safety device prevents unintentional use of the appliance. Control panel Switch on the appliance (Do not set a heat setting) Touch Touch until the signal sounds Acoustic signal Display/Signal Appliance switches off. Overriding the child safety device The child safety device can be released in this way for a single cooking session; it remains activated afterwards. Touch Control panel Switch on the appliance and at the same time / acoustic signal Display/Signal Until the appliance is next switched off, it can be used as normal. After overriding the child safety device, a heat setting or a function must be set within approx. 10 seconds, otherwise the appliance automatically switches itself off. Releasing the child safety device Step 1. Touch Touch Control panel Switch on the appliance until the signal sounds Acoustic signal Display/Signal Appliance switches off. The child safety device is released. operating the appliance electrolux 15 Using the timer Function Automatic cut-out Condition a heat setting is set Outcome after the time has elapsed acoustic signal 00 flashes Cooking zone switches off acoustic signal 00 flashes Countdown timer cooking zones not in use If a heat setting is set on this cooking zone in addition to a countdown timer, the cooking zone is switched off after the time set has elapsed. If a cooking zone is switched off, the timer function set is also switched off. 16 electrolux operating the appliance Selecting a cooking zone Step 1. Switch the appliance on again The lock is switched on Switch off the lock (See the section "Locking/unlocking the control panel") Remove objects. Acoustic signal sounds when appliance is switched off The residual heat indicator is not displaying anything The control panel is wholly or partly covered by objects. The cooking zone was only on If the cooking zone is supfor a short time and is therefore posed to be hot, call the Cusnot hot tomer Service Department. Let the cooking zone cool down The automatic warm up func- There is still residual heat on tion is not switching itself on the cooking zone The highest heat setting is set The highest heat setting has the same power as the automatic warm up function The heat setting was set using 1. Switching off the cooking the sensor field zone 1. Set the cooking zone using the sensor field Acoustic signal sounds and The On/Off sensor field has appliance switches itself on been covered up, e. g. by a and then off again; after 5 sec- cloth onds another acoustic signal sounds is lit Do not place any objects on the control panel Overheating protection for the Switch off the cooking zone. cooking zone has been trigSwitch the cooking zone on gered again Automatic switch off has been Switch off the cooking zone. triggered Switch the cooking zone on again what to do if . . . electrolux 25 Problem and number are displayed Possible cause Electronics fault Remedy Disconnect the appliance from the electrical supply for a few minutes (Take the fuse out of the house's wiring system) If after switching on again, is displayed again, call the customer service department and minus are displayed Light rays that are too strong Briefly shade the control panel, on the control panel, for exam- for example with the hand ple bright sunlight Acoustic signal sounds, appliance switches itself off Switch appliance on (again) If you are unable to remedy the problem by following the above suggestions, please contact your local Service Force Centre. Warning!Repairs to the appliance are only to be carried out by qualified service engineers. Considerable danger to the user may result from improper repairs. If the appliance has been operated incorrectly, the engineer's visit will be chargeable, even during the warranty period. 26 electrolux disposal Disposal Packaging material The packaging materials are environmentally friendly and can be recycled. The plastic components are identified by markings, e. g. [. . . ] Loose and inappropriate plug and socket connections can make the terminal overheat. Have the clamping connections correctly installed by a qualified electrician. In the event of single-phase or twophase connection, the appropriate mains cable of type H05BB-F Tmax 90C(or higher) must be used. If this appliance's mains cable is damaged, it must be replaced by a special cable (type H05BB-F Tmax 90C; or higher). [. . . ]