User manual AEG-ELECTROLUX MSCOMELECTRONICENGEN

[. . . ] USE & CARE MANUAL THIS AIR CONDITIONER IS EQUIPPED WITH A NEW INDUSTRY STANDARD POWER SUPPLY CORD WITH A TEST-RESET FUNCTION READ AND SAVE THESE INSTRUCTIONS AIR CONDITIONER MULTI-STEP SPEED ELECTRONIC CONTROL P/N 220201d011 SZ000302(En)-YaoKong(1018) 1 10/25/2004, 2:33 PM ROOM AIR CONDITIONER WARRANTY Your product is protected by this warranty Your appliance is warranted by Electrolux. Electrolux has authorized Frigidaire Consumer Services and their authorized servicers to perform service under this warranty. Electrolux authorizes no one else to change or add to any of these obligations under this warranty. Any obligations for service and parts under this warranty must be performed by Frigidaire Consumer Services or an authorized Frigidaire servicer. WARRANTY FRIGIDAIRE, THROUGH ITS AUTHORIZED SERVICERS, WILL: Pay all costs for repairing or replacing parts of this appliance which prove to be defective in materials or workmanship. [. . . ] The power supply cord is now supplying electricity to the unit. (On some products this is also indicated by a light on the plug head). Operation of Current Device NOTES: · · · · Do not use this device to turn the unit on or off. Always make sure the RESET button is pushed in for correct operation. The power supply cord must be replaced if it fails to reset when either the TEST button is pushed, or it cannot be reset. A new one can be obtained from the product manufacturer. If power supply cord is damaged, it CANNOT be repaired. It MUST be replaced by one obtained from the product manufacturer. Key Features (On some model) Multi-Step Fan and Cooling Speeds: 90 distinct fan settings give the ultimate in airflow and noise control. Clean Air: An ionic air filtration system that substantially increases the air-cleaning efficiency over conventional air filters. The Clean Air button on the air conditioner Touch Pad ONLY activates this feature. Air Conditioner Features ON/OFF LIGHT ELECTRONIC CONTROL OPERATING INSTRUCTIONS Before you begin, thoroughly familiarize yourself with the control panel and remote as shown below and all its functions, then follow the symbol for the functions you desire. The unit can be controlled by the touch pad alone or with the remote. ADJUSTS TEMP & TIMES FAN SPEEDS DISPLAYS TEMPERATURE/TIME FAN SPEED ADJUSTS TEMPERATURE OR TIME SETS MODES ACTIVATES TIMER SETS FAN SPEEDS ACTIVATES TIMER REMOTE CONTROL Fig. "A" ON/OFF LIGHT CHECK FILTER RESET BUTTON AUTO COOL FEATURE SLEEP MODE ADJUSTS TEMP & TIMES SETS MODE FAN SPEEDS CLEAN AIR FEATURE (some models) REMOTE TEMP. SENSING INDICATOR (SOME MODELS) TURNS UNIT ON OR OFF SETS MODES ACTIVATES REMOTE THERMOSTAT REMOTE CONTROL w/DISPLAY & REMOTE SENSING BUTTON ACTIVATES TIMER TOUCH PAD Fig. The fan then cycles on for 2 minutes at 10 minute intervals until the room temperature is above the set temperature, at which time the compressor turns back on and cooling stars. DO THIS: PRESS MODE BUTTON CHOOSE ENERGY SAVER 7 SZ000302(En)-YaoKong(1018) 7 10/25/2004, 2:33 PM Air Conditioner Features (continued) TIMER: DELAY STOP / START FEATURE YOU WILL SEE: TIMER SETTING LIGHT On Note: For Delay Stop, the unit must be in the On position. DO THIS: Note: For Delay Start, the unit must be in the Off position. PRESS TIMER BUTTON To adjust timer setting, tap or hold the UP arrow(^) or the DOWN arrow(V) to change delay timer at . 5 hour increments, up to 10 hours, then at 1 hour increments up to 24 hours. The control will count down the time remaining until start (8, 7. 5, 7, etc. ). The Delay Start mode automatically selects cooling with maximum Fan Speed. The temperature maintained will be the same as previously set. To change the set temperature, press "COOL" then Up or Down arrows until the desired temperature is indicated on the display. After 5 seconds, the control will automatically change the display back to the hours remaining until the unit will start/stop. Turning the unit "ON" or "OFF" at any time will cancel the Delay Start/Stop function. SLEEP FEATURE: YOU WILL SEE: LIGHT On DO THIS: PRESS SLEEP BUTTON Note: In this "MODE" the selected temperature will increase by 2 degrees F 30 minutes after the mode is selected. The temperature will then increase by another 2 degrees F after an additional 30 minutes. This new temperature will be maintained for 7 hours before it returns to the originally selected temperature. This ends the "Sleep" MODE and the unit will continue to operate as originally programmed. The "Sleep" MODE program can be cancelled at any time during operation by again pressing the "Sleep" button. 8 SZ000302(En)-YaoKong(1018) 8 10/25/2004, 2:33 PM Air Conditioner Features (continued) CHECK FILTER FEATURE: YOU WILL SEE: LIGHT On Note: This feature is a reminder to clean the Air Filter (See Care and Cleaning) for more efficient operation. [. . . ] Turn Control ON and set to desired setting. Air from unit does not feel cold enough. Room temperature below 60°F (16°C). Cooling may not occur until room temperature rises above 60°F (16°C). Temperature sensing element touching cold coil, located behind air filter. Wait approximately 3 minutes and listen for compressor to restart when set in the COOL mode. Air conditioner cooling, but room is too warm - ice forming on cooling coil behind decorative front. Outdoor temperature below 60°F (18°C). [. . . ]