User manual AEG-ELECTROLUX ÖAS2071-4GT

[. . . ] Never stop a tumble dry before the end of the drying cycle unless all items are quickly removed and spread out so that the heat is dissipated. Important safety information Environment Installation Product description Control panel Before first use Programmes 58 60 60 64 64 65 66 Daily use Drying rack Care and cleaning What to do if . Subject to change without notice In the interest of your safety and to ensure the correct use, before installing and first using the appliance, read this user manual carefully, including its hints and warnings. To avoid unnecessary mistakes and accidents, it is important to ensure that all people using the appliance are thoroughly familiar with its operation and safety features. [. . . ] Once in its permanent operating position, check that the dryer is absolutely level with the aid of a spirit level. If it is not, raise or lower the feet until it is. Do not restrict the floor clearance through deeply carpets, strips of wood or similar. This might cause heat built-up which would interfere with the operation of the appliance. The appliance must therefore not be installed on floors which are not resistant to high temperatures. When operating the tumble dryer, the room temperature must not be lower than +5°C and higher than +35°C, as it may affect the performance of the appliance. Should the appliance be moved, it must be transported vertically. The appliance must not be installed behind the lockable door, a sliding door or a door with a hinge on the opposite side to that of the appliance. removing transport safety packaging Caution!Before use all parts of the transport packaging must be removed. Pull off adhesive strips from inside machine on top of drum. Re-insert cover plates Bon the opposite site having first rotated them through 180°. Unscrew cover plates D from the front of the machine, rotate through 180°, screw on the opposite side. Unscrew door lock E, push down slightly and remove from the front of the machine. Press snap-in button F in and down, press cover down slightly and remove from front of the machine. Change door lock E over to the opposite side, screw down the door interlock. 8 Rating plate 9 Loading door (reversible) 10 Heat exchanger door, fluff filter, heat exchanger 11 Button for opening door in plinth 12 Ventilation grille 13 Adjustable feet Iron dry (drying phase indicator) light dry (drying phase indicator) cupboard dry (drying phase indicator) Strong dry (drying phase indicator) extra dry (drying phase indicator) cooling (drying phase indicator) crease guard (drying phase indicator) empty water reservoir (warning) clean condenser (warning) clean filters (warning) child lock Display description dryness default minimal dryness medium dryness maximal dryness spin speed default minimal spin speed spin speed scope (200 rpm step) - If the appliance was not transported in an upright position, leave it to stand for 12 hours before connecting it to the electricity supply and using it for the first time, so that the oil can flow back to the compressor. Otherwise the compressor could be damaged. at the beginning of drying cycle (3-5 min. ) there could be a slightly higher sound level. In order to remove any residues which may have been produced during production, wipe the dryer drum with a damp cloth or carry out a brief drying cycle (ca. Extra dry (Extratrocken) Intensive dry (Starktrocken) Cupboard dry (Schranktrocken) Iron dry (Bügeltrocken) All without Time (Zeiwahl) all without Time (Zeiwahl) all without Time (Zeiwahl) all without Time (Zeiwahl) Extra dry (Extratrocken) Cupboard dry (Schranktrocken) Iron dry (Bügeltrocken) To dry thin fabrics which are not ironed, e. [. . . ] Automatic process; this is not a machine fault. Select time programme or higher drying level (e. E51- only dryers with the LCD): Switch the dryer off and on. 2) follow program recommendation - see Programme overview chapter 3) see Care and cleaningchapter 4) see Machine settings chapter 5) only dryers with the LCD 6) Note: After around 5 hours the drying cycle ends automatically (see Drying cycle complete section). [. . . ]