User manual AEG-ELECTROLUX PE8036-M

[. . . ] A B 2/88 C D E/1 E/2 F/1 3/88 F/2 G H I/1 I/2 I/3 4/88 L M/1 M/2 N/1 N/2 O/1 5/88 O/2 P/1 P/2 Q/1 Q/2 Q/3 6/88 Q/4 Q/5 Q/6 Q/7 Q/8 R/1 7/88 R/2 R/3 R/4 R/5 R/6 R/7 8/88 R/8 S/1 S/2 S/3 9/88 INDEX 12. Technical assistance and spare-parts. 13. Steam tap knob Coffee measuring knob Switch button (ON/OFF) Coffee button Hot water button Steam button Light key "Power ON" Warning light Water temperature indicator Coffee indicator Water indicator Steam indicator Light indicator Coffee measuring indicator (1 short- , long coffee, 2 short - , long coffees) 1. Filter-holder ring nut Steam pipe Coffee pressing tool Coffee grinder button Coffee measuring device Cabinet block button Drip tray Coffee container Water reservoir Grinding regulation knob Filter-holder 1-cup-filter 3. [. . . ] Check that the red light of the water temperature indicator (B26) is out or wait until it will be. Push coffee button (B-21) and the coffee measure that comes out will be exactly the one selected and previously programmed. Take the filter-holder out of the ring nut and remove the coffee grounds. · USE OF COFFEE POD (E. S. E system) E. S. E. system means Easy Serving Espresso and corresponds to the international standard for brewing coffee using coffee pods (one throwaway portion of roasted coffee) and a suitable coffee machine. system is easy, practical and ecological because it doesn't need particular servicing and it is environmentally friendly. Moreover it is also a clean way to drink coffee thanks to its special packaging that avoids coffee to come out and can be removed after use. The machine can work also with pods: one throwaway portion of roasted coffee (for one single coffee only). Put the knob (B-19) on the required coffee measure (long or short single coffee). HOT WATER · · · Put a container under the steam pipe (A-2). Turn the steam knob counterclockwise (B-18). Push the hot water button (B-22) and the delivered water measure will be the same as previously programmed. Close the steam knob (B-18) · · · 9. STEAM LIQUIDS ` HEATING · Press once the steam button (I/1); both the steam indicator (B-29), and the water 8/23 · · · · · · · temperature indicator will be ON (B-26). Wait until both of them will be out (I/2). Push the steam button again in order to stop producing steam (B-23). To check if the steam has been produced push again the steam button (I/3); if the water temperature indicator l(B-26) remains out it means that steam is ready to come out. Put under the steam pipe (A-2) a container with the liquid that has to be warmed . Turn the steam knob counterclockwise (B-18) Wait until the liquid becomes warm. Close the steam knob (B-18) Attention: never make coffee when the steam is ready to come out, if this is the case, reset the water level in the boiler as explained in the next point. Attention: after every steam emission push the hot water button (B-22) without opening the steam knob (B18) (in this way the water level in the boiler will be reset). · · · · · · · · · 29), and the water temperature indicator will be ON (B-26). Wait until both of them will be out (I/2). [. . . ] They should be used to compensate the internal width of the seat. For obtaining a width of 562/560mm see picture P/1 e P/2. INSTALLATION WITHOUT SUPPORT · Put the suitable plates (P/1, P/2) on the both sides of the embedding seat, fixing them with the double-sticker strips (Q/1). Pay attention to the position of the bevel which indicates the right position of the plates. [. . . ]