User manual AEG-ELECTROLUX PN 3500 X

[. . . ] Do not incinerate the battery cartridge even if it is severely damaged or is completely worn out. the battery cartridge can explode in a fire. Be careful not to drop or strike battery. Before using battery cartridge, read all instructions and cautionary markings on (1) Charge the battery cartridge when you notice less tool power. [. . . ] When the reversing switch lever is in the neutral position, the switch trigger cannot be pulled. cAUTION: · Always check the direction of rotation before operation. Use the reversing switch only after the tool comes to a complete stop. Changing the direction of rotation before the tool stops may damage the tool. When not operating the tool, always set the reversing switch lever to the neutral position. Always be sure that the tool is switched off and the battery cartridge is removed before adjusting or checking function on the tool. Always be sure that the tool is switched off and the battery cartridge is removed before carrying out any work on the tool. Always switch off the tool before insertion or removal of the battery cartridge. To remove the battery cartridge, withdraw it from the tool while sliding the button on the front of the cartridge. To insert the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Always insert it all the way until it locks in place with a little click. Depress the reversing switch lever from the A side for clockwise rotation or from the B side for counterclockwise rotation. Straight head and ratchet head (Accessory) Straight heads and ratchet heads are available as optional accessories for various applications on the job. The proper fastening torque may differ depending upon the kind or size of the screw/bolt, the material of the workpiece to be fastened, etc. Before starting your job, always perform a test operation to determine the proper fastening time for your screw. Use the proper bit for the head of the screw/bolt OPERATION that you wish to use. If the tool is operated continuously until the battery cartridge has discharged, allow the tool to rest for 15 minutes before proceeding with a fresh battery. the fastening torque is affected by a wide variety of factors including the following. After fastening, always check the torque with a torque wrench. When the battery cartridge is discharged almost completely, voltage will drop and the fastening torque will be reduced. Driver bit or socket bit Failure to use the correct size driver bit or socket bit will cause a reduction in the fastening torque. Even though the torque coefficient and the class of bolt are the same, the proper fastening torque will differ according to the diameter of bolt. [. . . ] Even though the diameters of bolts are the same, the proper fastening torque will differ according to the torque coefficient, the class of bolt and the bolt length. The manner of holding the tool or the material of driving position to be fastened will affect the torque. For Model PN 3500 X ENG102-1 For European countries only Noise The typical A-weighted noise level determined according to 60745-2-2: Sound pressure level (LpA): 91 dB (A) Sound power level (LWA): 102 dB (A) Uncertainty (K): 3 dB (A) Wear ear protection Vibration ENG205-1 The vibration total value (tri-axial vector sum) determined according to EN60745-2-2: Work mode : impact tightening of fasteners of the maximum capacity of the tool Vibration emission (ah): 9 m/s2 Uncertainty (K): 1. 5 m/s2 For Model BTL061 ENG102-1 For European countries only Noise The typical A-weighted noise level determined according to 60745-2-2: Sound pressure level (LpA): 90 dB (A) Sound power level (LWA): 101 dB (A) Uncertainty (K): 3 dB (A) Wear ear protection Vibration ENG205-1 The vibration total value (tri-axial vector sum) determined according to EN60745-2-2: Work mode : impact tightening of fasteners of the maximum capacity of the tool Vibration emission (ah): 11 m/s2 Uncertainty (K): 1. [. . . ]