User manual AEG-ELECTROLUX PN64

[. . . ] Before the appliance is connected: 1) check that the main fuse and the domestic installation can support the load (see the rating label); 2) check that the power supply is properly earthed in compliance with the current rules; 3) check the socket or the double pole switch used for the electrical connection can be easily reached with the appliance built in the forniture unit. Before switching on, make sure the electricity supply voltage is the same as that indicated on the appliance rating plate. The rating plate is located on the bottom of the hob. A copy is attached on the back cover of this book. [. . . ] Before connecting the gas supply pipe to the joint (C), the installer will ensure that the paint drop is unbroken and the "L" connector has not been moved by the vibrations during handling and transportation. When the final connection has been made, it is essential that a thorough leak test is carried out on the hob and installation. Ensure that the main connection pipe does not exert any strain on the hob. FO 1010 A) End of shaft with nut B) Washer C) Adjustable joint Cut Out Size The dimensions of the cut-out are given in the diagram. Rectangular cut-out size for hob 55 m in. 480 560 Dimensions are given in mm. FO 2038 150 min 10 Instructions for the Installer Engineer technical data OVERALL DIMENSIONS Width: Depth: Height: Weight: 580 mm. 11 Kg. Supply Connections Gas: RC 1/2 inch (1/2 inch male) Rear right hand corner Electric: 230 V 50Hz supply, 3 core flexible cable with non rewireable plug. Appliance Gas supply: LPG 30 mbar Appliance Class: 3 Appliance category: I 3 CUT OUT DIMENSIONS Width: 560 mm. Thickness: 30 mm. Burner Nominal Power kW kCal/h 814 1368 2475 LPG (Butane "A") Nozzle 50 65 85 g/h 75 126 228 Diameter Tap. By-Pass 28 35 45 Feeding Pressure mbar (*) Auxiliary (dia. 90 mm. ) 0, 95 1, 60 2, 9 30 (*) 1 mbar = 10 mm. water coloumn. 9 Something Not Working? If the appliance is not working correctly, please carry out the following checks before contacting your local Service Centre. SYMPTOM n There is no spark when lighting the gas SOLUTION u Check that the unit is plugged in and the electrical supply is switched on. u Check the burner cap and crown have been replaced correctly, e. g. u Check the main jet is not blocked and the burner crown is clear of food particles. u Check the burner cap and crown have been replaced correctly, e. g. after cleaning. n The gas ring burns unevenly If after all these checks, your appliance still does not operate correctly, contact your local Service Centre. 8 Maintenance and Cleaning Before any maintenance or cleaning can be carried out, you must DISCONNECT the hob from the electricity supply. The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool. The Hob Top Regularly wipe over the hob top using a soft cloth well wrung out in warm water to which a little washing up liquid has been added. Avoid the use of the following: - household detergent and bleaches; - impregnated pads unsuitable for non-stick saucepans; - steel wool pads; - bath/sink stain removers. Should the hob top become heavily soiled, it is recommended that a cleaning product such as Hob Brite or Bar Keepers Friend is used. FO 2237 Pan Supports To keep the pan supports in the correct position, they are hooked into hinges at the back of the hob. The pan supports can be lifted for easier cleaning, as shown in fig. To remove the pan supports completely, proceed as shown in fig. If washing them by hand, take care when drying them as the enamelling process occasionally leaves rough edges. If necessay, remove stubborn stains using a paste cleaner. Fig. 1 The Burners The burner caps and crowns can be removed for cleaning. Wash the burners taps and crowns using hot soapy water, and remove marks with a mild paste cleaner. [. . . ] Remove all packaging before using the appliance. Ensure that the gas and electrical supply complies with the type stated on the rating plate, located near the gas supply pipe. Do not attempt to modify the appliance in any way. l When using other electrical appliances, ensure the cable does not come into contact with the hot surfaces of the cooking appliance. Unstable or misshapen pans should not be used on the hob as unstable pans can cause an accident by tipping or spillage. [. . . ]