User manual AEG-ELECTROLUX RH360D

[. . . ] For warranty or service, please contact our customer services section. Spares can be obtained all over Europe from our relevant customer service points. When contacting customer service, please always state model, product and serial number!You can find this information on the model label inside the device. e. g. 3 4. 0 4. 1 INSTALLATION The Purpose of this Manual The manual shows you how to: install the miniBar correctly. [. . . ] The ventilation grid must not be covered, for example, by ornaments or items of clothing. The miniBar must always be mounted horizontally. 5 4. 6. 1 4. 6 Securing RH356LDE 1. Put on cap. 4. 6. 2 RH136, RH137, RH330, RH340, RH341, RH360, RH361 The miniBar must be screwed onto the cupboard using the lower hinges. 1. Put on cap. 4. 6. 3 Old Version RH136, RH137 1. Tighten screw. 6 4. 7 Connecting the Device to the Electricity Supply The device must be connected to a properly earthed socket in line with the relevant valid country regulations. Check prior to initial operation that the voltage noted on the model label corresponds to the mains voltage. If this is not the case, do not connect the device and contact your dealer! 4. 7. 1 Plug connection (for United Kingdom only) Warning - This appliance must be earthed. IMPORTENT Attention: For GB Only ! If a 3-pin plug is used, it should be fitted with a 3 amp fuse, with other plug types, the circuit should contain a 5 amp fuse. The wires in the mains lead of this appliance are coloured in accordance with the following code: GREEN and YELLOW : EARTH BLUE : NEUTRAL BROWN : LIVE As the colours of the wires in the mains lead may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows. Connect the GREEN and YELLOW coloured wire to the plug terminal marked letter E or earth symbol or coloured green or green and yellow. Connect the BROWN coloured wire to the plug terminal marked letter L or coloured red. Connect the BLUE coloured wire to the plug terminal marked letter N or coloured black. Moulded-On Plug Version The mains lead is fitted with a non-rewirable moulded-on plug containing a 3 amp fuse. If the fuse requires replacing at any time, the fuse cover/carrier should be removed using a small screwdriver to level out. When the door is opened, the light in the cooling shelf is switched on via a sensor. The light in the uncooled storage shelf is switched on manually by means of a switch integrated into the lamp. 5. Clip reflector disk back in. 5. 6. 2 When the door is opened, the light in the cooling shelf is switched on via a sensor. Changing bulbs: Interior Light (All other models) 1. Clip reflector disk back in. To obtain spare bulbs, please contact your Electrolux Service Centre. 12 5. 7 miniBars manufactured by Electrolux Siegen are free from CFCs and fluorinated hydrocarbons. The cooling unit uses ammonia as the coolant (a natural compound of hydrogen and nitrogen). Cyclopentane, which does not damage the ozone layer, is used as propellant for the insulation made from PU-foam. Enviromental Advice 5. 8 In order to ensure the re-use of recyclable packaging materials, these must be disposed of using local collection systems. The device itself must be handed over to a disposal company or local council which will guarantee the correct use of recyclable materials and the proper disposal of the rest. Disposal 5. 9 Energy Saving Tips At an average room temperature of approx. 22°C, it is sufficient to operate the miniBar with an average thermostat setting. If possible, always store pre-cooled goods. Do not expose the miniBar to direct sunlight and do not place it close to a source of heat. [. . . ] Self Help a. ) Level the device using a spirit level. b. ) Switch on the device and let it run for 5-6 hours. Possible Cause a. ) The cooling aggregate is not sufficiently ventilated. Self Help a. ) Check that the ventilation grids are not covered. [. . . ]