User manual AEG-ELECTROLUX RM4361LM

[. . . ] The appliance, which works silently, meets high quality standards and guarantees the efficient utilisation of resources and energy throughout its entire life cycle, during manufacture, in use and when being disposed of. Before you start to use the appliance, please read the installation and operating instructions carefully. The refrigerator is designed for installation in leisure vehicles such as caravans or motorcaravans. The appliance has been certified for this application in accordance with EU Gas Directive 90/396/EEC. 2. 0 2. 1 FOR YOUR SAFETY Danger Attention Warning and safety notices Never use a naked flame to check the appliance for leaks. [. . . ] Check that the ventilation grilles and the extractor have not been blocked by snow, leaves or similar. Lower ventilation grille ( L200 ) Upper ventilation grille with flue vent ( L100) 2. When the ambient temperature falls below +8C, the optional winter covers should be fitted. This protects the unit from excessively cold air. 3. It is also recommended that the winter covers should be used when the vehicle is taken out of TIP service for an extended period of time. 5. 10 Interior light (when fitted) Changing the light bulbs 1. Fit new light bulb. Note: for 12V DC : 1 light bulb 8V, 2W for 24V DC : 2 light bulbs 28V, 1, 5W 4. Clip the cover back in place. Please contact Dometic Service centres for replacement light bulbs. 11 5. 11 Changing the decor panel 1. Open the door and loosen the hinge screw. 2. Take off the door by moving it upwards. 3. Unscrew the door strip (3 screws). 4. Remove the decor plate and insert a new decor plate. 5. Screw the door strip back in position. 6. In this case an authorised Dometic representative may issue supplementary instruction In Europe, for example, gas appliances, cable laying, installation of gas cylinders, as well as approval and checking for leaks must comply with EN 1949 for liquid gas units in vehicles. 6. 1 Installation The appliance and its fume extraction shall be installed in such a way as to be accessible for servicing at all times and must be capable of easy removal and installation. The appliance may only be installed by authorised personnel. Installation and connection of the appliance must comply with the latest technical regulations, as follows: European Standard EN 1949 European Standard EN 732 The electrical installation must comply with national regulations ( EN 1648-1 , EN 1648-2 , EN 60335-2-24 for Europe). The gas installation must comply with national regulations. Local and building control department requirements The appliance shall be installed in such a way that it is shielded from excessive heat radiation. Excessive heat impairs performance and raises the energy consumption of the refrigerator. Any installation that is not carried out by qualified persons will jeopardize the manufacturer's guarantee. 6. 1. 1 Side Installation If the appliance is installed on the same side of the vehicle as the entrance door, it is desirable that the door does not cover the refrigerators vents. If this cannot be avoided there must be a gap of at least 25mm between the door and the vents. 6. 1. 2 Rear installation If the refrigerator is mounted at the rear of the vehicle you must ensure the lower grille is not covered by the bumper or rear lights. This would be prevent the air from circulating properly and cause problems in warm weather. Air vent grille not blocked: OK!Fig. 2 17 6. 2 Draught-free installation Proposal 1: The refrigerator must be sealed in accordance with EN 1949. Illustrated below are two typical approved methods of sealing. Using the Installation Sealing Kit from Dometic (SP. No. [. . . ] The gas connection to the appliance must be installed securely and at zero potential using tube connectors and must be securely connected to the vehicle (a hose connection is not permissible) (EN 1949). Inflamable material should not be in immediate proximity to the burner. 23 The gas connection to the appliance is effected by means of a suitable coupling tube fitting L8, DIN 2353-ST, complying with European Standard EN 1949 (e. g. The gas connection may only be carried out by a qualified personnel. SW 17 SW 14 Following proper installation, a testing for leakage and a flame test must be carried out by *qualified personnel in compliance with EN1949 . [. . . ]