User manual AEG-ELECTROLUX SANTO3092KG

[. . . ] These operating instructions are for use with several technically comparable models with varying accessories. Please observe the notes which apply to your model. Notes which are important for your safety or for the proper functioning of the appliance are stressed with a warning triangle and/ or with signal words (Warning!, Caution!, Important!). This symbol guides you step by step in the operation of the appliance. [. . . ] The plug socket necessary for connection of the appliance to the electricity supply should be positioned, so that the plug is not placed in the recess. To adjust the height proceed as follows: Loosen or tighten the two front feet. 596 5 55 x ma - 2Li89 + The rear feet are adjusted by turning the screw in the front kick plate to the left or right. If necessary, pads are supplied for the rear feet to make sliding the appliance in and out of the recess easier. To fit the pads, press them onto the rear feet. If required, the dimensions of these pads can be reduced by breaking them where marked. 2/a II52 11 N. B. The joint cover (B) is to be assembled after having installed the appliance in the recess. 2 B 1 3 115° 4 Push the appliance into place and retain the cabinet with screws through the securing brackets into the worktop or adjacent woodwork as necessary. 5 12 To mount the furniture door proceed as shown in the figures: 10 1 2 a C 4 3 b 6 7 a C clic C b clic 8 c 13 Upper part of kitchen furniture panel 1 = a Lower part of kitchen furniture panel = 2 275 275 ma x1 00 9 b 9/a 1 45 ° 2 3 10 = 10 = 11 14 12 Refit the covering strip. A 13 15 Fitting the plinth Important!For the efficient operation of the appliance, it is important that the original ventilation grid is used. The rating plate is inside, on the left. The appliance is supplied with a 13 amp plug fitted. In the event of having to change the fuse in the plug supplied, a 13 amp ASTA approved (BS 1362) fuse must be used. FUSE The wires in the mains lead are coloured in accordance with the following code: Green and Yellow Earth Blue Neutral Brown Live BROWN As the colours of the wires in the mains lead BLUE CORD CLAMP of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: 1. The wire coloured green and yellow must be connected to the terminal marked with the letter "E" or by the earth symbol or coloured green and yellow. Tip: Food in the fridge should always be covered or packaged, to prevent drying and tainting of other food. The following are suited for packaging: ­ Polyethylene airtight bags and wraps; ­ Plastic containers with lids; ­ Special plastic covers with elastic; ­ aluminium foil. Defrosting The fridge defrosts automatically The rear wall of the fridge covers with frost when the compressor is running, and defrosts when the compressor is off. The water from the thawing frost evaporates by itself. 20 Switching off the appliance To switch off the appliance, turn the temperature regulator to positi on "0". If the appliance is not going to be used for an extended period: Remove all refrigerated packages. Switch off the appliance by turning the thermostat knob to position "0". Remove the mains plug or switch off or disconnect from the electricity supply. Clean thoroughly (see section: "Cleaning and Care"). Leave the door open to avoid the build up of odours. Cleaning and Care For hygienic reasons the appliance interior, including interior accessories, should be cleaned regularly. · The appliance must not be connected to the mains during cleaning. Before cleaning switch the appliance off and remove the plug from the mains, or disconnect from the electricity supply. [. . . ] To change the light bulb, undo the screw. Press the light bulb cover as shown and slide it backwards. Refit the light bulb cover and the screw. Put the refrigerator back into operation. AEG65 24 Service & Spare Parts In the event of your appliance requiring service, or if you wish to purchase spare parts, contact your local AEG Service Force Centre by telephoning: 08705 929 929 Your call will be automatically routed to the Service Centre covering your post code area. [. . . ]