User manual AEG-ELECTROLUX SANTO7088KG

[. . . ] These operating instructions are for use with several technically comparable models with varying accessories. Please observe the notes which apply to your model. Notes which are important for your safety or for the proper functioning of the appliance are stressed with a warning triangle and/ or with signal words (Warning!, Caution!, Important!). This symbol guides you step by step in the operation of the appliance. [. . . ] The following table shows which ambient temperature is correct for each climate classification: Climate classification SN N ST T for an ambient temperature of +10 to +32 °C +16 to +32 °C +18 to +38 °C +18 to +43 °C If the refrigeration appliance is installed next to another refrigerator or freezer a clearance of 5 cm at the sides is required, in order to prevent the formation of condensation on the outside of the appliance. 7 Reversing the door The side at which the door opens can be changed from the right side (as supplied) to the left side, if the installation site requires. When changing the side at which the door opens, remove plug from the mains. Left door opening: Remove the grid from the appliance by pulling it towards. Remove the left side (A) of the grid cutting it from the rear (see figure). A Re-install the grid to the base of the appliance by pushing the clasps (a) until they click. a a 8 To reverse the opening direction of the door, proceed as shown in the figures: 9 Building the appliance in under a worktop The dimensions of the recessed installation area must correspond with those indicated in the figure. 60 0 55 min0 . 600 Remove covering and adjust the bracket locking nuts. Push the appliance into place. The plug socket necessary for connection of the appliance to the electricity supply should be positioned, so that the plug is not placed in the recess. Adjust height. 10 Mounting furniture door 11 Screw appliance into place. Place the covering strip. 12 Fitting the plinth Important!For the efficient operation of the appliance, it is important that the original ventilation grid is used. · For an opening height dimension A=820 mm and a plinth height dimension a=100 mm, the plinth may be fitted without adjustments. The same applies to an opening height dimension B=870 mm and a plinth height dimension b=150 mm. · For plinth heights greater than 580 a=100 mm, b=150 mm, a cut should 25 be made in the plinth, 580 mm wide, ÷8 0 in the centre of the appliance 25 position, leaving a remaining height 008 of a=100 mm, b=150 mm. · Attach plinth to the kitchen units. A = 820 B = 870 Important!The plinth must be positioned at a minimun distance of 25 mm from the door. Please check whether, after installing your appliance and especially after reversing the door, the door seal seals right round. Tip: Food in the fridge should always be covered or packaged, to prevent drying and tainting of other food. The following are suited for packaging: ­ Polyethylene airtight bags and wraps; ­ Plastic containers with lids; ­ Special plastic covers with elastic; ­ aluminium foil. 17 Defrosting The fridge defrosts automatically The rear wall of the fridge covers with frost when the compressor is running, and defrosts when the compressor is off. The water from the thawing frost evaporates by itself. Switching off the appliance To switch off the appliance, turn the temperature regulator to positi on "0". If the appliance is not going to be used for an extended period: Remove all refrigerated packages. Switch off the appliance by turning the thermostat knob to position "0". Remove the mains plug or switch off or disconnect from the electricity supply. Clean thoroughly (see section: "Cleaning and Care"). Leave the door open to avoid the build up of odours. Cleaning and Care For hygienic reasons the appliance interior, including interior accessories, should be cleaned regularly. · The appliance must not be connected to the mains during cleaning. Before cleaning switch the appliance off and remove the plug from the mains, or disconnect from the electricity supply. · Never clean the appliance with a steam cleaner. [. . . ] Light bulb is defective. Remedy Please look in the "Initial Start Up" section. Do not leave the door open any longer than necessary. Turn the thermostat knob to a colder setting temporarily. Please look in the "Installation location" section. [. . . ]