User manual AEG-ELECTROLUX ST 500

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual AEG-ELECTROLUX ST 500. We hope that this AEG-ELECTROLUX ST 500 user guide will be useful to you.

Lastmanuals help download the user guide AEG-ELECTROLUX ST 500.


Mode d'emploi AEG-ELECTROLUX ST 500
Download
Manual abstract: user guide AEG-ELECTROLUX ST 500

Detailed instructions for use are in the User's Guide.

[. . . ] It is recommended to wear gloves, sturdy non slipping shoes and apron. J Sawdust and splinters must not be removed while the machine is running. J Do not pierce the motor housing as this could damage the double insulation (use adhesives). J Keep mains lead clear from working range of the machine. [. . . ] Revolutions by means of the hexagonal allen key (fitted into the base plate). Fit the saw blade into the groove of the support roller And push it firmly into the plunger as far as it will go; the lug of the saw blade must contact the end of the plunger (see illustration). Check that the saw blade is sitting firmly (wear Adjusting the base plate The base plate can be tilted or moved backward or forward. Loosen the fixing screw, pull the base plate out of the mounting, set it at the required angle (15o, 30o, 45o), push it back into the mounting and tighten the fixing screw again. Angles other than 45o can be set by not pushing the base plate back into the mounting. For very exact angle cuts it is recommended to make a test cut. Moving the base plate Loosen the fixing screw, push the base plate to the rear and tighten the fixing screw again. The base plate in this position is fixed at the 0o setting. Moving back For cutting a hole with a short saw blade and sawing near the edge. Take the fixing screw out, push the base plate to the rear and screw the fixing screw tightly into the rear hole. In this position the base plate can also be off-set in longitudinal direction. Push in and turn the suction hose into the Push the transparent cover downwards to The anti-splintering device almost entirely prevents the edge of the wood from splintering. Place the anti-splintering device as shown in the illustration with the smooth side downwards and flush with the base plate (this is only possible with the base plate in the forward position). The stroke rate appropriate to the material being worked on can be taken from the following table, and the corresponding letter shown on the setting wheel. Intermittent use Switching on: Press On-/off switch Switching off: Release On-/off switch Continuous use Switching on: Press the On-/off switch and then the locking button, after that release on-off switch. Adjusting the pendulum stroke (only applicable for STEP 500) ENGLISH 4 By adjusting the pendulum action the cutting depth of the saw blade teeth is increased or decreased. As a rule of thumb: Soft material Hard material Clean cut surface Large pendulum stroke Small or no pendulum stroke No pendulum stroke ST 500, STE 500, STEP 500 The letters A to G are printed on the speed control, meaning: A = lowest stroke rate G = highest stroke rate The stroke-rate (= movements per minute of the saw blade) can be infinitely varied by means of the adjustment wheel. The appropriate degree of pendulum effect can be taken from the following chart and compared with the marking at the pendulum stroke lever. The stroke rate can be set on the stroke rate control even while the motor is running. Position the machine with the front part of the base plate on the material, and Press the machine downwards onto the material and guide it along the cutting line. [. . . ] bend up both lugs and remove the plastic protection shoe. Further accessories with part numbers are shown in our catalogues. In order to guarantee constant readiness for operation, the machine should be checked for worn carbon brushes at one of the AEG after­sales service agencies. Use only AEG accessories and spare parts. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE AEG-ELECTROLUX ST 500

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual AEG-ELECTROLUX ST 500 will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag