User manual AEG-ELECTROLUX TR1238

[. . . ] The button then must be held in for three seconds to activate the machine. DOOR At the end of its life the machine must be disabled before being scrapped. Contact your local recycling centre to find out where to dispose of it or recycle it. The machine has been built and marked to facilitate recycling. The door is opened electrically, so it cannot be opened until the machine is connected to the electrical supply!The door can however be opened in an emergency, see Troubleshooting. OVERFILL CUT-OUT If the water level in the machine rises above normal the overfill cut-out shuts off the water intake and starts pumping out the water. [. . . ] The held in for three seconds to activate the machine. THERMAL CUT-OUT Recycle the packaging according to recommendations in your area. SCRAPPING The tumble dryer is protected by a thermal cutout. This switches off the machine if it gets too hot. FLOAT (only applies to condenser dryer) At the end of its life the machine must be disabled before being scrapped. Contact your local recycling centre to find out where to dispose of it or recycle it. The machine has been built and marked to facilitate recycling. A float switches off the machine if there is a blockage in the condensed water hose. CAUTION! During the programme, the back of the tumble dryer will get very hot. Leave the machine to cool completely before touching the back. SAFETY TUMBLE DRYER 17 PARTS OF THE TUMBLE DRYER 3 4 2 1 1 2 3 4 5 6 7 8 8 5 6 7 1. CONDENSATION WATER TANK ­ CONDENSER TUMBLE DRYERS ONLY 4. CONDENSER ­ ONLY CONDENSER TUMBLE DRYERS (BEHIND FRONT PANEL) 8. LINT FILTER TUMBLE DRYER PARTS OF THE TUMBLE DRYER 18 TECHNICAL INFORMATION TECHNICAL DATA Height: Width: Depth: Weight: Drum capacity: Drying capacity: Speed: Power rating: Composition of drum: Composition of casing: Installation: Drain (condenser tumble dryer): Vent hose (venting tumble dryer): PROGRAMME CYCLES 850 mm. Powder-painted and hot-dip galvanized sheet steel or stainless steel. 3. 0 m PVC. Cooling Temperature Drying 20 20 20 20 20 20 20 20 (appr. min) P1 Extra dry P2 Dry P3 Normal dry P4 Iron dry P5 Extra dry P6 Dry P7 Normal dry P8 Iron dry Normal Normal Normal Normal Low Low Low Low The length of the drying depends on the moisture of the items being dried. Slide the vent hose over the end of the adapter and secure with the plastic strap. Remove the plastic cover from the hole if you intend to connect the hose to a hole other than the one that is already open. Insert the end of the adapter in the hole. Fit the cover to the open hole. Connecting to vent duct max 1000 mm NOTE! It is important that you use the new rubber hose that is supplied, not an old hose. VENTING (only applies to venting tumble dryer) The vent hose must follow the shortest, straightest path possible from the tumble dryer to the vent duct. Cut the vent hose to length if it is too long. If necessary the vent hose can be extended to a maximum length of 8 metres (internal diameter 102 mm). If a longer hose is required it must have a larger internal diameter in order to maintain the fan capacity of the dryer. Any bends should be as gentle as possible. If The exhaust air from the tumble dryer must be led to a ventilation duct or a wall outlet using the accompanying vent hose. Connecting to tumble dryer Examples of installations The tumble dryer can be vented in three ways: from the rear, from the right side or from the left side. One of the holes is open when the dryer is delivered. The other two 3 2 1 are fitted with covers. [. . . ] To cancel an error message after the fault has been corrected as described below, switch off the machine or change the programme. You can check and fix some faults yourself: Over flow. Indicating that the condensation water tank is full or that the lower water magazine is full, due to the pump or hoses being clogged or malfunctioning. Empty the tank and check to ensure there are no kinks or blockage in the hose. [. . . ]