User manual AEG-ELECTROLUX TWISTER Z5835 EURO

[. . . ] Save these instructions and make sure that they remain with the appliance if it is moved or sold, so that everyone using it through its life will be properly informed on appliance use and safety. - Please read the instruction book before using this appliance. general safety · It is dangerous to alter the specifications or attempt to modify this product in any way. This appliance is not intended for use by persons (including children) with reduced physical and sensory conditions or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. [. . . ] Only tip the appliance on its left side to transport (see illustration), if it cannot be transported in an upright position. The appliance must not be installed behind the lockable door, a sliding door a door with a hinge on the opposite side to that of the appliance in such a way that a full opening of the dryer is restricted. removing transport safety packaging Caution!Before use all parts of the transport packaging must be removed. If the appliance was not transported in an upright position, leave it to stand for 12 hours before connecting it to the electricity supply and using it for the first time, so that the oil can flow back to the compressor. Otherwise the compressor could be damaged. appliance positioning · It is recommended that, for your convenience, the machine is positioned close to your washing machine. The tumble dryer must be installed in a clean place, where dirt does not build up. Air must be able to circulate freely all round the appliance. Do not obstruct the front ventilation grille or the air intake grilles at the back of the machine. To keep vibration and noise to a minimum when the dryer is in use, it should be placed on a firm, level surface. Read carefully the instructions supplied with the kit. Unscrew hinge A from the front of the machine and take off the loading door. To do this, insert a thin screwdriver into the slots as shown in the illustration, press downwards slightly and pry out the cover plates. Use an appropriate tool and exert pressure to unfasten locking block C from the snap-on fixture, take out and re-insert on the other side having rotated the block through 180°. Unscrew hinge A from the loading door, rotate through 180°, re-insert on the opposite side and screw down. Re-insert cover plates B on the opposite site having first rotated them through 180°. Unscrew cover plates D from the front of the machine, rotate through 180°, screw on the opposite side. Unscrew door lock E , push down slightly and remove from the front of the machine. Press snap-in button F in and down, press cover down slightly and remove from front of the machine. Change door lock E over to the opposite side, screw down the door interlock. 1 2 3 4 5 6 7 Control panel Water reservoir Drum light Fine fluff filter Course fluff filter Fluff filter Rating plate 8 Loading door (reversible) 9 Heat exchanger door, fluff filter, heat exchanger 10 Button for opening door in plinth 11 Ventilation grille 12 Adjustable feet Iron dry (drying phase indicator) light dry (drying phase indicator) cupboard dry (drying phase indicator) Strong dry (drying phase indicator) extra dry (drying phase indicator) cooling (drying phase indicator) crease guard (drying phase indicator) empty water reservoir (warning) clean condenser (warning) clean filters (warning) child lock long anti-crease buzzer time Time to end / error message cycle phase status options warnings spin speed selection dryness selection Display description dryness default minimal dryness medium dryness maximal dryness spin speed default minimal spin speed spin speed scope (200 rpm step) - If the appliance was not transported in an upright position, leave it to stand for 12 hours before connecting it to the electricity supply and using it for the first time, so that the oil can flow back to the compressor. [. . . ] 5) No drum light Abnormally elapsing time on the LCD5) Programme inactive Drying cycle to short Attempt to change parameters after start of the programme. Turn it to DRUM LIGHT (if available) or to any programme. Automatic process; this is not a machine fault. empty water reservoir3) , press START PAUSE button. [. . . ]