User manual AEG-ELECTROLUX UK5755

[. . . ] 2-4 Upright Vacuum Cleaner Owner's Guide Household Type IMPORTANT INFORMATION GUARANTEE QUICK REFERENCE HOW TO ASSEMBLE HOW TO USE ROUTINE MAINTENANCE 4 5-6 7-8 8-9 Z5750 Series 10 11 12 Dust Cup Dust Cup Filter Side Door Filters PERIODIC MAINTENANCE 13 13 IMPORTANT For any advice on your cleaner and to order filters and accessories, please telephone the Electrolux Helpline on Brush Roll Brush Roll Belt PROBLEM SOLVING 14 14 15 Mini Turbo Nozzle Clear Hose Guide 08706 055055 www. electrolux. co. uk When using an electrical appliance, basic precautions should always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS VACUUM CLEANER. IMPORTANT SAFEGUARDS WARNING · To reduce the risk of fire, electric shock, or injury: · Do not use outdoors or on wet surfaces. · Do not leave vacuum cleaner when plugged in. Turn off the switch and unplug the electrical cord when not in use and before servicing. · Do not allow to be used as a toy. [. . . ] Do not pinch electrical cord between handle and cleaner. Attach Hose 3 Electrical Cord 1 Grooves Upper Hose Retainer 2 4 Hose Lower Hose Retainer HOW TO ASSEMBLE 1 From rear of cleaner, align handle with groove and slide onto cleaner. If necessary, use thumb and finger pressure to slide handle into position. Attach handle with two 1 inch screws provided in the assembly packet. Use a Phillips® head screwdriver. 3 4 2 Pick up hose and lay across upper hose retainer. Push the end of the hose in the lower hose retainer to secure. Hose NOTE: Hand tighten with screwdriver to be sure both screws are firmly seated. Models Equipped with Spin Duster Install Spin Duster · Fit the Duster to hose retainer so cup is forward and next to the vacuum dust cup. · Push end of hose into opening on top of Duster. Screw Hose Retainer SIDE OF CLEANER 7 Store Hose and Accessories Nested Extension Tubes Store Electrical Cord 5 Cord Retainer 6 Cord Hook Dusting Brush HOW TO ASSEMBLE HOW TO USE 8 Handle Release. Step on handle release to pull handle back to a comfortable operating position. To lower handle completely to the floor, depress handle release a second time. 6 Cord Hook 5 You will find your cord retainer on the handle above the upper cord hook. Firmly push the electrical cord down into the cord retainer. This will place the cord out of the way the next time you vacuum. Next wind the cord around the two cord hooks on the back side of cleaner. 6 Cleaner Height Setting. Keep loose clothing, hair, adjustment that raises or lowers fingers, and all other parts of body the cleaner base to match the away from any moving part (such type of floor surface. Turn off the cleaner cord unplugged, set the switch and unplug the cleaner before adjustment to lowest setting for changing the cleaner height setting. If the cleaner is difficult to push, move adjustment to next highest setting until cleaner is comfortable to push. The brush roll must reach the carpet for effective cleaning. For ease in moving the adjustment knob, place handle in operating position and tilt cleaner back to remove weight from front wheels. Store Helpful Information: Operate Before cleaning under low furniture, check area first for objects that might harm the unit or block the vacuum hose. Clean Under Models Equipped with Spin Duster How To Use · Turn on vacuum, leaving cleaner in the upright (parked) position. · Depress and hold lever to divert air suction into Duster. · Allow Duster to spin for 10-15 seconds prior to first use. This action creates a static charge on the duster and also cleans it after each use. [. . . ] 8 Lock Button 9 10 11 Remove hood from cleaner and check for a blockage in the brush roll area. After the blockage is found and cleared, replace the hood on the cleaner. Place lower hose adapter back into the base hose. Install the upper hose adapter onto the back of the cleaner, line it up with the cleaner opening and push it against the cleaner until both tabs lock into place. Mini Turbo Nozzle 14 NOTE: Turn off the switch and unplug the electrical cord before servicing. PROBLEM Motor will not start. CAUSE Electric Plug SOLUTION Push plug securely into outlet. [. . . ]