User manual AEG-ELECTROLUX WD8126EL

[. . . ] User manual Washer-dryer WD 8126 EL Thank you for selecting our appliance We wish you lots of enjoyment with your new appliance and we hope that you will consider our brand again when purchasing household appliances. Please read this user manual carefully and keep it throughout the product life cycle as a reference document. The user manual should be passed on to any future owner of the appliance. The following symbols are used in this manual: Important information concerning your personal safety and information on how to avoid damaging the appliance. General information and tips Environmental information Content Safety information - - - - - - - - - - - - - - - - - - -3 Description of the appliance - - - - - - - - - - - -5 Detergent dispenser drawer - - - - - - - - - - - -5 Control panel and functions - - - - - - - - - -6-8 Programme table - - - - - - - - - - - - - - - - -9-10 Programme information - - - - - - - - - - - - - -11 Washing and drying hints - - - - - - - - - - - - -12 Before the first use - - - - - - - - - - - - - - - - -15 Operating Sequence - - - - - - - - - - - - - - - -15 Washing - - - - - - - - - - - - - - - - - - - - - - - - -15 2 Drying - - - - - - - - - - - - - - - - - - - - - - - - - -19 Drying programmes - - - - - - - - - - - - - - - - -20 Care and cleaning - - - - - - - - - - - - - - - - - -21 What to do if. . [. . . ] The incorrect option selection is indicated by the message Err displayed for few seconds and by the red light button of button 8 blinking. 17 Altering an option or a running programme It is possible to change any option before the programme carries it out. Before you make any change, you must pause the machine by pressing button 8. Changing a running programme is possible only by resetting it. Turn the programme selector dial to «O» and then to the new programme position. Start the new programme by pressing button 8 again. The washing water in the tub will not empty out. Interrupting a programme Press the button 8 to interrupt a programme which is running, the corresponding light starts blinking. Press the button again to restart the programme. Cancelling a programme Turn the selector dial to «O» to cancel a programme which is running. Opening the door after the programme has started First set the machine to pause by pressing the button 8. If the light 9 goes off, the door can be opened. If it does not go off, this means that the machine is already heating, that the water level is above the bottom edge of the door. In this cases the door cannot be opened. If you cannot open the door but you need to open it you have to switch the machine off by turning the selector dial to «O». The door can be opened after few minutes. (Pay attention to the water level and temperature!). After this procedure, it will be necessary to set the programme and the options again and then to press the button 8. At the end of the programme The washer dryer stops automatically. Some acustic signals sound and on the display will appear a blinking «0 ». The button 8 light and the light 9 go off. If, at the end of a programme, there is water in the tub (light 9 still on), to empty out the water follow the following instructions: To empty out the water: 1. turn the programme selector dial to «O» 2. reduce the spin speed, if needed, by means of the button 2 4. [. . . ] Before connecting the machine to new pipework or to pipework that has not been used for some time, run off a reasonable amount of water to flush out any debris that may have collected in the pipes. Electrical connection This machine is designed to operate on a 220230 V, single-phase, 50 Hz supply. Check that your domestic electrical installation can take the maximum load required (2. 2 kW), also taking into account any other appliances in use. Connect the machine to an earthed socket. [. . . ]