User manual AEG-ELECTROLUX WRG980CGS

[. . . ] M Please dispose of those materials through your local recycling depot or by placing them in appropriate collection containers. ·fyouwishtodiscardthisproduct, pleasecontact I your local authorities and ask for the correct method of disposal. Exhaust cover ceiling mounting bracket Telescopic exhaust cover set Flexible exhaust pipe Exhaust duct transition Main body mounting brackets Main body and fan housing assembly Grease filters Instruction book Model: Power supply: Motor: Lights: Model: Power supply: Motor: Lights: WRG970CS 220 ­ 240 volts 50Hz. input power 200 watts 2 x 20 watt 12 volt halogen WRG980CGS 220 ­ 240 volts 50Hz. input power 200 watts 2 x 20 watt 12 volt halogen ADDITIONAL ITEMS REQUIRED FOR INSTALLATION ·Fixings required to attach main body mounting brackets and anti-tilt fixings. [. . . ] If installed in recirculating mode, insert the optional carbonfilterincludedinrecirculationkitAR600RK formodelWRG970CSandAR600RKGformodel WRG980CGS. To complete the rangehood installation, insert the three filters to the underside of the hood body. Place back edge of filter into position and push up front edge so that the filter clips into place. Your Westinghouse rangehood is now ready to use. USING THE RANGEHOOD - WRG980CGS Low Medium High Distance from hood base to top of hob hob type minimum* maximum gas 650mm 800mm electric 600mm 800mm * TO OPERATE CANOPY If the instructions of the hob specify a greater distance than the minimum above, then that shall be the minimum height for installation USING THE RANGEHOOD - WRG970CS NOTE: For ducted mode, we recommend extending flue pipe through the roof to external "china hat" to vent exhaust externally. We do not recommend venting into ceiling cavity. (Refer optional ducting accessories on page 9). NOTE: To ensure optimum performance of the rangehood, the use of rigid ducting is recommended. Rigid flexible ducting is suitable, although loose flexible ducting is unacceptable. All ducting must be fire retardant. Touch any of the fan symbols, depending on desired fan speed, to turn the canopy on. Touch the OFF button to turn canopy off. SETTING THE POWER LEVEL REQUIRED 2. Mark the location for the wall and ceiling bracket fixing points above the hood base using the hood base as the reference point (refer diagram previous page). Install wall and ceiling mounting brackets with suitable screws (to support a total weight of 30kg) to the wall at the positions marked in diagram bottom left. Remove the protective plastic film from the hood body and hang hood on the mounting brackets then secure at the anti-tilt locations as indicated in diagram bottom left. Depending on the preferred installation/ducting mode, follow step 5a or 5b below. Using the centre line, secure the ceiling mount bracket to the wall using suitable screws. Attach the recirculating T-piece (optionalkitAR600RKformodelWRG970CS or AR600RKGformodelWRG980CGS)totheceiling mount bracket. Install flexible pipe between T-piece and fan transition outlet. Use cable ties or suitable duct tape to secure flexible pipe to T-piece. NOTE: When installed in recirculation mode, it is recommended to use a carbon filter (included in recirculation kit AR600RK for model WRG970CS or AR600RKG for model WRG980CGS, refer to page 9) to prevent odours being emitted back into the room. OR All symbols have illumination above. Fan operation ­ select speed to suit cooking conditions. Low ­ light frying/boiling Low Medium High TO OPERATE CANOPY Medium ­ frying/wok cooking/heavy boiling High ­ grilling, intensive frying and wok cooking TO SWITCH LIGHTS ON AND OFF INSTALLATION OF TELESCOPIC EXHAUST COVERS Separate the inner and outer exhaust covers, and carefully remove the protective coating from both. Carefully reassemble the inner and outer exhaust covers sections by sliding the inner into the outer exhaust cover. [. . . ] This warranty only applies to Appliances purchased and used in Australia or New Zealand and is in addition to (and does not exclude, restrict, or modify in any way) any non-excludable statutory warranties in Australia or New Zealand. 3. During the Warranty Period Electrolux or its ASC will, at no extra charge if your Appliance is readily accessible for service, without special equipment and subject to these terms and conditions, repair or replace any parts which it considers to be defective. Electrolux or its ASC may use remanufactured parts to repair your Appliance. You agree that any replaced Appliances or parts become the property of Electrolux. [. . . ]