User manual AEG-ELECTROLUX Z5020

[. . . ] In this case, the use of carbon filters is absolutely necessary (see FIG. Carbon filters are available separately and can be purchased as optional accessories (see OPTIONAL ACCESSORIES). Before mounting you should be aware of: 2. 1) Check that the minimum distances between the lower part of the cooker hood and the upper part of the cooker is as given in Fig. [. . . ] to mount the chimney please proceed as follows: · The 2 parts of the chimney are mounted as shown in FIG. 7; · Position the base part of the chimney with holes matching the ones on the hood; · Insert the screws if available, on the bottom of the chimey and fix them; · Let the telescopic part of the chimney slide to the height necessary to touch the ceiling and come into contact with the chimney bracket; · 4 GENERAL WARNING The pipe must be heat, flame and corrosionproof. The producer strongly advises against the use of reducers or pipes with smaller diameter than the hood outlet pipe, and pipes made of flexible aluminium because performance is diminished. The end part of the pipe, on the outside of the hole on the wall, must be of such a shape to avoid rain, gusts of wind or other foreign bodies getting into the pipe. Should there be any doubt, contact anyone specialising in the installation of gas or ventilation system. 1 WARNING The electrical connection can only be carried out by qualified professional personnel, using standard material and state of the art installation methods. The manufacturer declines any responsibility for installations carried out by unskilled persons and for installations which are not in conformity with the standard norms concerning electrical safety (both concerning methods and materials). 2 ELECTRICAL TECHNICAL DATA The electrical technical data are visible inside the hood after the removal of the grease filters. 3 CONNECTION TO THE POWER SUPPLY The flexible feed cable supplied is already connected internally and emerges from the hood near the air outlet duct. Check that the electrical data indicated are in conformity with the main voltage and frequency values of the building where the hood is to be installed; · Check that the building is fitted with electric safety systems to protect against short circuits and electric shock systems, according to the laws in force; · Install an electric socket (or connection point) with a bipolar switch, which has contacts with an opening of at least 3 mms; · If it is intended to install the hood with a plug, it is necessary that you have access to the plug. Always turn off the main voltage supply by means of the bipolar switch before connecting and switch on again only when connections have been completed, tested and are safe. Push the push-buttons 0 (zero) and T (timer) at the same time for a few seconds. 4 SETTING THE SUCTION /FILTERING USE OF THE HOOD The hood is delivered standard for suction use (only with flashing F letter). If you wish to use it in the filtering version (F and C flashing) proceed as follows: and T on the display for about 5 seconds, the following symbol will press the buttons appear followed by a 0. At each pressure of the Light Button, it is possible to change the value shown from the O (suction function), to 1 (filtering function) and viceversa. To activate the functions connected to these push buttons, it is necessary to apply a little pressure just lightly and for a short time. If pressure is too lengthy on the push buttons the connected functions are not activated. The functions activated by the push buttons are as follows: LIGHTS: switch the lights on and off; TIMER: if pressed when the hood is already functioning with 1st, 2nd, 3rd or 4th speed, the led point connected with the selected speed, starts to flash for 10 minutes, after which motor automatically stops. MEANING OF THE LED POINTS: if the leds connected with the speeds are flashing, there is a timing running. 1st Speed; 2nd Speed; 3rd Speed; 4th Speed; 5th Speed; led point is flashing; 6th Speed; led point is flashing. 5th and 6th Speed must be used just for short periods as the hood is taking in a big quantity of air so after 10 minutes the motor is automatically reset to the 3rd speed. 2 AUTOMATIC CONTROL OF GREASE AND CARBON FILTER the electronic controls with led points allow automatic control of the grease filters and carbon filters (only in case the hood is used in filtering version) so that the user does not have to remember when maintenance was last carried out. [. . . ] Put the filter- cassette on the grill of your oven and let it warm up for 1 hour at 230°C. Then wait for 2 hours to let it become completely cold. Only after this time the filter can be remounted and your hood can work for other 4 months. If you use the hood in an intensive way, the filter must be regenerated in shorter time. [. . . ]