User manual AEG-ELECTROLUX Z6160

[. . . ] The appliance is not intended for use by young children and infirm persons without supervision. Allow steam-cleaned carpets to dry out thoroughly. - Matches, glowing ashes or cigarette ends. - Toner dust (from laser printers and copiers). [. . . ] 89/336/EEC dated 03. 05. 89 (including Directive Amendment 92/31/EEC) - EMC Directive. This appliance complies with the following EU Directives: 3 Exploded view and assembly A B C D E F G H Cable retraction button Cable Display Change exhaust air filter Suction power regulator ON/OFF button Display: Change dustbag Dust chamber release catch right/left: Retainer lid for SUPER_PRO accessories Suction hose Accessories retainer Power regulator on handle Telescopic tube with furniture protection ring N Floor nozzle O Appliance handle J K L M M N 4 Vacuuming Pull out cable B and insert plug into mains. (to retract cable, pull out mains plug, hold plug firmly, and press button A. ) Switch on/off by pressing button E (there is the possibility of a delay in starting of up to 4 seconds at the lowest power level due to electronic starting current limitation). Set suction power using suction power regulator D. This can also be reduced by opening the power regulator on handle L in order to vary the amount of strength required to push the vacuum cleaner. 5 Nozzles N Floor nozzle, setting may be changed for carpets and hard floors. If you have a carpet/hardfloor nozzle with two pedals-press the pedal on the right to vacuum up animal hair, etc. P Combination nozzle: furniture brush and upholstery nozzle in one R Crevice nozzle (extendable) Q Handle with removable suction hose 6 Special accessories Easy clean kit The easy clean kit efficiently cleans fragile objects, such as plants, lamps and porcelain. The airflow created in the container continually cleans the duster and maintains a static charge. Hardfloor nozzle The special nozzle is for use on parquet, tiled and hard floor. Mini set 4 special nozzles and brushes plus a flexible mini hose for cleaning technical appliances and delicate parts. Turbo nozzle The turbo nozzle makes the care of carpets easier. The rotary motion of its brush gently loosens short-pile carpets where the dirt has been trodden in. It removes stubborn fluff and pet hairs. 7 Changing dustbag Change dustbag S when display F is filled with colour (can be checked with the appliance operating at maximum suction and with the nozzle raised from the floor). A change may be necessary even if the bag does not appear to be full. Fine dust can block the pores and reduce the suction power of the appliance. Switch off the appliance and open the dust chamber lid by pulling release catch G. Remove dustbag S by pulling on the sealing tab. Push new dustbag into the retainer until it clicks into place. Take care when closing the dust chamber lid that the dustbag is completely inside the dustchamber border. The dust chamber lid will not close unless a dustbag has been inserted. Please do not use force! S E54AB Standard S-bag, E202B Clinic S-bag, E203B Anti Odour S-bag, S-bag Long Performance 8 Changing the Filters Change motor protection filter T if display F is still filled with colour after the dustbag has been changed or if the suction power is significantly reduced although the dustbag has little in it. Switch off the appliance and open the dust chamber lid by pulling release catch G. Replace microfilter V if display C is filled with colour or after every fifth dustbag change or if the suction power is significantly reduced / Clean HEPA filter X if display C is illuminated: Switch off the appliance. Press filter grille button U and open filter grille W. [. . . ] Check dustbag, suction tube and suction hose; remove any blockage. The appliance can be switched on again after approximately 30 minutes. the fuse has blown: The fuse can be blown if other electric appliances with a high power con-sumption are used at the same time and on the same circuit as the vacuum cleaner. If this is the case, set the suction power regulator to the lowest setting before switching on and only select a higher suction level after switching on. [. . . ]