User manual AEG-ELECTROLUX ZE2420

[. . . ] · Damage to the machine's cable is not covered by the warranty. · Never pull or lift the vacuum cleaner by the cable. · Disconnect the plug from the mains before cleaning or maintenance of the vacuum cleaner. · Regularly check that the cable is not damaged. [. . . ] The vacuum cleaner stops · Check if Ergobox is full. If so, empty it and clean both the box and the filter before putting it back in the cleaner. · If in the case as above the cleaner may have overheated which has activated the thermal overload protection, wait approximately 30 minutes before using the machine, in this time the overload protection will have reset. · Is the nozzle, tube or hose blocked?Water has entered the vacuum cleaner It will be necessary to replace the motor at an authorised Electrolux service centre. Damage to the motor caused by the penetration of water is not covered by the warranty. Troubleshooting 22 23 24 25 Cleaning the hose and nozzle Putting Ergobox back MakesureErgoboxandthefiltersaredry. Makesurethemotorfilterisinplace. (See alsoTakingcareofthefilter(s). )Makesure thewashableHEPAfilterisinplace. (See alsoTakingcareofthefilter(s). ) 28 Fix the front and rear parts together with the 3 hooks. Close the catch by fixing the metal fastening. 29 Put Ergobox back in the cleaner. The vacuum cleaner stops automatically if the nozzle, tube, hose or filters become blocked. In such cases, disconnect from mains and allow to cool for 20-30 minutes. Clear blockage and/or replace filters and restart. Tubes and hoses 34 Use a cleaning strip or similar to clear the tubes and hose. Hose handle could be dismantled from hose if cleaning is needed. 35 It may also be possible to remove the obstruction in the hose by squeezing it. However, be careful in case the obstruction is caused by glass or needles caught inside the hose. 26 27 28 UsingtheEasycleankit:TheEasyclean kithastobefixedbetweenthetubeand thehandle(12). Takethedusteroutofthe containertocleanfragileobjects, frames, bookshelves, etc. (12a)Pullthetriggertoclean theduster(12b). Theairflowcreatedinthe containercleansthedusterandmaintainsa staticcharge. Crevices, corners, etc. : Use the crevice nozzle (6). Store upholstery and crevice nozzle with the clip on the hose handle*. Taking care of the filter(s) Themoreoftenthebetterfortheefficiency ofthecleaner. Neverusethevacuumcleaner withoutfilter(s). A Motor-filter (Ref. EF 54) Grasp the Ergobox dust container and lift it out as shown in the illustration 23. 30 Pull the filter holder upwards until it comes away from the groove. Carefully pull the old, dirty filter(s) out of the filter holder and replace with a new filter(s). 31 Reinstall the filter holder containing the new filter(s). Washable Ergobox dust container HEPA filter (Ref. Cleaning of the washable Ergobox dust container HEPA filter (Ref No. [. . . ] 25 Remove the cover (rear part) carefully and empty possible remaining dust. 27 Turn the washable HEPA filter anticlockwise and pull it away. To put a clean one back, push and turn it clockwise. Emptying the Ergobox dust container ItisrecommendedtowashtheHEPAfilter eachtimeErgoboxisemptied. Washitwith abrushunderataporwashitinawashing machine(max. temperature60°). Letthe filterdrybeforeputtingitback. Alwaysmake surethatthefilteryouputinErgoboxiscom. pletelydryandclean, butdonotspin-dry C Exhaust filter There are three types** of exhaust filter: · Microfilter* (Ref. EF 17) · HEPA H12* non-washable (Ref. [. . . ]