User manual AEG DD 8891 M9

[. . . ] € La distance minimum entre la superficie de support des récipients sur le dispositif de cuisson et la partie la plus basse de la hotte de cuisine ne doit pas être inférieure à 50cm dans le cas de cuisinières électriques et de 65cm dans le cas de cuisinières à gaz ou mixtes. Extérieure): Hauteur (recyclage): Largeur: Profondeur: Puissance nominale totale: Moteur: Eclairage: Longueur du câble: Branchement électrique: 85, 5-129, 5 96-140 59, 8 39 290 W 250 W 2 x 20 W 150 cm 220-240 V DD 9893 85, 5-129, 5 96-140 89, 8 39 290 W 250 W 2 x 20 W 150 cm 220 - 240 V Accessoires/Matériel de montage 1 manchon de réduction 1 déflecteur (avec rallonge) 1 clé à chenillette pour vis torx 1 support de fixation pour le groupe moteur 1 support de fixation cheminées (3 pièces à assembler) 6 vis 5 x 45 mm 6 chevilles Ø 8 mm 2 vis 2, 9 x 6, 5 8 vis 3, 5 x 6, 5 4 vis 4 x 8 2 bouchons grand modèle 2 bouchons petit modèle 57 Branchement électrique Consignes de sécurité pour l’électricien La tension électrique doit correspondre à la tension reportée sur la plaque signalétique située à l’intérieur de la hotte. Assembler le support cheminée (3 parties) Les trois parties doivent être fixées entre elles avec 4 vis, l’extension du support est réglagle et doit correspondre à la largeur interne de la cheminée téléscopique. 81 63 Safety warnings • When used as an extractor unit, the hood must be fitted with a hose having preferably the same diameter as the outlet hole. [. . . ] Always comply with the maintenance instructions for the grease filter. Charcoal filter LED (C) The charcoal filter LED C will start to flash when the charcoal filter needs to be replaced. This operation is necessary after approximately 160 working hours. Resetting the saturation indicator After cleaning or replacing the filters, press button 3 for 3 seconds until the grease filter LED F or the charcoal filter LED C stops flashing. Before performing any maintenance operation, isolate the hood from the electrical supply by switching off at the connector and removing the connector fuse. Or if the appliance has been connected through a plug and socket, then the plug must be removed from the socket. Air suction panels Remove the perimeter air suction panels to access the grease filters. € DD 9893 The perimeter air suction panels are attached to the cooker hood by a series of pins and coupling springs; pull them outwards and detach them from the fastening cable. 3 When refitting the perimeter air suction panels, ALWAYS reattach the fastening cables. Make sure the panels are attached to the cooker hood properly (snap-fastened). 3 70 • DD 9863 Pull the panel (FRONT SIDE) downward with decision, unscrew safety knob and unhook it from the rear hinge. 3a Proceed in the reverse order when refitting it. 3a Clean the perimeter air suction panels as often as the grease filters (for more information about gentle cleaning methods, read the paragraph “Cleaning” in the pages that follow). Inner crosspiece - DD 9893 The inner crosspiece should be removed in order to access the grease filters and the inside of the cooker hood (for example: when performing maintenance work on the carbon filters). Keep the crosspiece supported during removal/fitting procedures, in order to prevent it from falling and damaging other objects. Remove it from its position using the spring release system. Re-fit the crosspieces by carrying out the above steps in reverse. Make sure the crosspiece is fixed to the cooker hood properly. 4 71 Metal grease filter • The purpose of the grease filters is to absorb grease particles which form during cooking and it must always be used, either in the external extraction or internal re-circulation function. Attention: the metal grease filters must be removed and washed, either by hand or in the dishwasher, every four weeks. Removing the metal grease filters • Push it towards the back of the unit and then pull it down and out. 5 Hand washing Soak grease filters for about one hour in hot water with a greaseloosening cleaner, then rinse off thoroughly with hot water. [. . . ] If provided with a plug connect the hood to a socket in compliance with current regulations and positioned in an accessible area. If it not fitted with a plug (direct mains connection) or if the plug is not located in an accessible area apply a bi-polar switch in accordance with standards which assures the complete disconnection of the mains under conditions relating to overcurrent category III, in accordance with installation instructions. IMPORTANT: Before re-connecting the hood circuit to the mains supply and checking the efficient function, always check that the mains cable is correctly assembled. Before beginning installation • In addition check whether near the installation area of the hood (in the area accessible also with the hood mounted) an electric connection to the mains is available and if it is possible to connect a fumes discharge device to the outside (Extraction mode only). [. . . ]