User manual AIPTEK PENCAM TRIO VGA+

[. . . ] AIPTEK PENCAM VGA + Installation Guide FCC Statement This equipment generates and uses radio frequency energy. If not installed and used in accordance with the manufacturer's instructions, it may interfere radio and television reception. This equipment has been tested and certified to comply with the limits of Section 15(J) of FCC Regulations for Class B computing devices. These regulations are designed to provide reasonable protection against interference in a residential installation. [. . . ] The camera will automatically power off after 30 seconds of inactivity. Press Mode button LCD will be light up Taking a picture Press the shutter button to take a picture. **A high pitched beep indicates that the picture was taken successfully and the counter will decrease accordingly. **A low beep indicates insufficient light to take a picture. Press the shutter button again, a short beep will be issued and the last picture will be deleted. Note: If the shutter button is not pressed within 5 seconds, the camera will go back to capacity mode. Shutter button Mode button Switch mode button to "CL" "CL" will be displayed Press the shutter button to select "CL" mode LCD will start blinking Press the shutter button again to clear the last memory Modes Selecting Clear all images Pressing the mode button until "CA" appears on LCD and then press the shutter button, the LCD will start blinking. Press the shutter button again and a short beep will be issued, and all the pictures in the camera will be deleted. Note 1: If the shutter button is not pressed within 5 seconds, the camera will go back to capacity mode. Note 2: Once the shutter button is pressed, all the pictures will be erased. Shutter button Mode button Switch mode button to "CA" "CA" will be displayed Press shutter button to select "CA" mode LCD will start blinking Press shutter button again to clear all images in the camera. Modes Selecting Changing the picture resolution When "Hr" is shown on LCD, which means present status is "High Resolution". If pictures are taken under this status, the format will be VGA (640*480). When "Lr" is shown on LCD, which means present status is "Low Resolution". If pictures are taken under this status, the format will be QVGA (320*240). Shutter button Mode button Switch mode button to "Hr" or "Lr" "Hr" or "Lr" will be displayed Press the shutter button to change resolution. Shutter button Mode button Modes Selecting Compressed mode Press the mode button until "CP" appears on LCD and press the shutter button, you will see default capacity change to 78 ( for "Hr") or 312 (for "Lr") for you to take more photos in the camera. Pressing the mode button until "nP" appears on LCD and pressing the shutter button again will go back to OnCompressed mode. Note 1: The mode shown on LCD is the mode you are going to switch. Note 2: "CP" stands for "Compressed Mode" and "nP" stands for "Mon-Compressed Mode. " Shutter button Mode button Switch mode button to "CP" or "nP" "CP" or "nP" will be displayed Press the shutter button to change compression Modes Selecting Flicker Settings Your camera has default flicker settings. If pictures in DV Disk mode appear unnatural flickering noise, please select "Cancel Flicker" in the setting dialog. ** See Table 2. Shutter button Mode button Switch mode to "F5" or "F6" "F5" or "F6" will be displayed Press the shutter button to change light frequence Country England Germany France Italy Spain Netherlands Setting 50Hz Portugal 50Hz 60Hz 50Hz 50Hz Japan 50Hz Country America Taiwan China Korea Setting 50Hz 60Hz 60Hz 50Hz 50/ 60Hz 60Hz Table 2. Software Installation Before downloading the taken pictures from the camera, you need to install the proper camera driver to your PC first. Please follow this guide for proper driver installation. Digital Camera Plus Manager Installation Place the CD into your CD-ROM. If there is no action for the CD-ROM, simply go to "Start" then "Run" and select the path "D:\Setup. exe". You may need to replace "D" with the letter that corresponds to your CD-ROM drive. Click on "Digital Camera Plus Manager" and your computer will initialize the Wise Installation Wizard. Please wait. Digital Camera Plus Manager The welcome screen will appear, then click "Next". The CD will begin installing the driver to the proper location. Hardware Installation Important Note: No matter what PC working panel you are using now, PLEASE always install the software first and then hardware. For Windows 98SE / ME User: The camera can be used immediately when connecting the camera and PC with USB cable directly. For Windows 2000 User: Plug in the USB cable and follow the system instruction to finish the installation. Click on "Yes" to continue the installation. Hardware Installation For Windows XP User: Plug in the USB cable and follow the system instructions to finish the installation. Select the recommend item and then click on "Next" to continue. Digital PemCam Plus has been found. [. . . ] If the HARDWARE PRODUCT is sold to another user by the original End-User, the Limited Warranty will be null and void, and AIPTEK will have no obligation to provide the Warranty Service. If the HARDWARE PRODUCT is a gift from the original purchaser to another person, then the Limited Warranty can be transferred to the recipient of the HARDWARE PRODUCT, provided the original purchaser does not attempt to open the box which the HARDWARE PRODUCT was packaged in. If this HARDWARE PRODUCT is purchased from an unauthorized reseller, the Limited Warranty will be null and void, and AIPTEK will have no obligation to provide the Warranty Service. See the "List of Authorized Resellers" in the manual to determine whether or not you purchased the HARDWARE PRODUCT from an Authorized Reseller. Only the End-User who has registered the product and who has kept a copy of the original receipt may receive the Warranty Service. [. . . ]