User manual AIRLIVE ARM-104 V3

[. . . ] ARM-104_v3 Wired ADSL 2/2+ Modem Router User's Guide AirLive ARM-104_v3 ADSL2/2+ Router i Copyright The contents of this publication may not be reproduced in any part or as a whole, stored, transcribed in an information retrieval system, translated into any language, or transmitted in any form or by any means, mechanical, magnetic, electronic, optical, photocopying, manual, or otherwise, without the prior written permission. AirLive ARM-104_v3 ADSL2/2+ Router ii FCC Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against radio interference in a residential environment. AirLive ARM-104_v3 can generate, use and radiate radio frequency energy and, if not installed and used in accordance with the instructions in this manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If AirLive ARM-104_v3 does cause harmful interference to radio or television reception, which is found by turning the equipment ON and OFF, the user is encouraged to try to reduce the interference by one or more of the following measures: Adjust or relocate the receiving antenna Increase the separation between the equipment or device Consult a dealer or an experienced technician for assistance CE Declaration of Conformity This is to certify that this device complies the essential protection requirements of the European Council Directive 89/336/EEC, Article 4a. [. . . ] Each SNMP-managed device has at least one agent that can respond to the queries from the NMS. The SNMP agent supports GETS, SETS, and TRAPS for 4 groups with MIB-II: System, Interface, IP, and ICMP. SNMP Agent: Click to enable the SNMP Agent. An SNMP agent is a node that resides on the network, typically a computer or a router. The SNMP agent is controlled and configured by the NMS by sending SNMP messages between one another. SNMP agents are logged and identified in a Management Information Base (MIB), in which they are identified by an object identifier (OID). SNMP Traps: Click to enable the SNMP Traps. SNMP traps are used to notify network managers of significant events that have taken place in the network. These traps are sent to the SNMP NMS ( NMS Server located at Trap IP ) through the specified Ports. Name: An administratively-assigned name for the ARM-104_v3 ADSL2/2+ Router. By convention, this is the node's fully-qualified domain name. Location: The physical location of the ARM-104_v3 ADSL2/2+ Router. Contact: Contact person and/or contact information for the ARM-104_v3 ADSL2/2+ Router. AirLive ARM-104_v3 ADSL2/2+ Router 73 Vendor OID: Vendor Object Identifier. Private MIDBs fit under OID 1. 3. 6. 1. 4. 1. The enterprise number of this device is 294. Note: The System Name, System Contact, and System Location can be up to 127 characters. Community: SNMP defines a community to be a relationship between an SNMP agent and one or more SNMP managers. Once the clear-text community name corresponds to a community known to the receiving SNMP entity, the sending SNMP entity is considered to be authenticated as a member of that community and is granted different levels of access: read-only or read-write. SNMP supports up to 3 communities including the default community name of "Public". Access Right: Two options are offered: ReadOnly: Allows a GET or a GETNEXT operation to all objects with access rights of READ-ONLY in the MIB. ReadWrite: Allows a GET or a GETNEXT operation to all objects with access rights of READ-WRITE in the MIB. There are 4 standard traps supported in this ARM-104_v3 ADSL2/2+ Router: WarmStartTrap, LinkUpTrap, LinkDownTrap, and AuthenticationFailureTrap. [. . . ] Subnet Mask: Short for SubNetwork Mask, subnet mask is a technique used by the IP protocol to filter messages into a particular network segment, called a subnet. The subnet mask consists of a binary pattern that is stored in the client computer, server, or router. This pattern is compared with the incoming IP address to determine whether to accept or reject the packet. TCP: Transfer Control Protocol: Works together with Internet Protocol for sending data between computers over the Internet. [. . . ]