User manual AIRLIVE CAMPRO EXPRESS 64

[. . . ] CamPro Express 64 64 Channel IP Camera Management Software User's Manual Copyright & Disclaimer No part of this publication may be reproduced in any form or by any means, whether electronic, mechanical, photocopying, or recording without the written consent of OvisLink Corp. has made the best effort to ensure the accuracy of the information in this user's guide. However, we are not liable for the inaccuracies or errors in this guide. All information is subject to change without notice All Trademarks are properties of their respective holders. i 1. [. . . ] Please note, if your video server is behind a router or firewall, you should need to do some extra setting on the network device, like virtual server or port forwarding. Please forward the server port and connection port to the video server. You might change those ports in the System Configure System Setting. 3. 5. 1 Remote Login: Open the IE browser and type the IP address or URL in the address bar. The login dialoge will show up, please enter the user name/passward set in the "System Configuration User Account". 33 3. 5. 2 Install the ActiveX After logining into the system, the IE will ask to install the ActiveX component. Please select "Install This Add-on for All Users on This Computer". 3. 5. 3 Remote Live View The explanations of the operation are as below: 34 Channel List: You can view up to 4 cameras remotely at the same time. The camera list can show each camera's current status. Each status is represented with different colors and their meanings are explained below: Camera is connected Camera is NOT connected Camera is current performing recording PTZ Control Panel: Use this function to control the P/T function of the camera. And use the Preset function to move the lens of the camera to a preset point. 3. 5. 4 Remote Sequence View button to enable/disable the audio button to take a picture of the critical The explanations of the operation are as below: 35 Channel List: Use the Channel List to select the desired cameras for sequence monitoring. You might use the "All Channels" or "All Groups" for select all cameras. Interval: Set the Interval time for each camera to dwell on the monitor. Start/Stop Button: Use to start or stop the sequence monitoring. 3. 5. 5 Remote Playback Start by selecting which channel(s) you would like to perform a search on: Note: Selected channels will be marked in red. Select "Search by time chart" from the "Search Method" dropdown list and the Time Chart will be shown on the page. Set the search conditions. The is, set the date period for searching. Results will then be displayed in a "Date/Channel" table and boxes 36 marked in gray represent videos found in those dates: Click on any gray cell box should direct you to the hour/channel table. Click on the gray cell on the hour/channel should direct you to the minute/channel table, if there were videos recorded during that date. By clicking on the "Back" button, the chart would return to the hour/channel table for you to re-select the time period. By clicking on the "Back to Top" button, the chart would return to the search mode select function for you to re-search the video clip. Note: Videos from other cameras that are recorded on the same date will also be displayed. 37 Click on the cell box again will start playing back the videos if you have reached the end of search results: Note: Videos found from other cameras that were recorded at the same time will also be played. 3. 5. 6 Remote User Setting Click on the User Account in the up-right coner, the User Information will show up. You might select the Web UI language for the user. 38 4 4. 1. 4. Configuring CamPro Express 64 System Configuration User can configure the Server Name, select the UI language, and assign the TCP ports in this area. Server Name: You might change the Server Name, and the name should appear in the Network Place for identification. [. . . ] Button: Use this button to cancel the configuration you made. 55 4. 6. Recording Setting Click on the button on the Overview tab for adding the folder to save the recording file. 4. 6. 1 4. 6. 2 Select the Recording Setting tab, and configure the values as explaining below: 56 Channel: Select the desired channel for configuring. Or just click on the channel on the list left to the configuration area for selecting the desired channel. Recording Mode: Please check if you would like the CamPro Express 64 to recording continuously or by schedule. I/P Frame: Choose if you would like the CamPro Express 64 to record only I frame or both I and P frame. [. . . ]