User manual AIRLIVE EPHONE-2000S

[. . . ] ePhone-2000S Wired IP Phone User's Manual AirLive ePhone-2000S -i- English Version AirLive ePhone-2000S <English Version> CONTENTS I. Airlive ePhone-2000S Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Rear View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] (3) Speed Dial [0-19] +SPD; e. g. : `1'+SPDor `01' + SPD SPD+ [00-19]; e. g. :SPD+ `01'. Note: if you want to dial single digit only, such as SPD+ 1, please press an additional #to finish dialing; otherwise, it will wait for the second digit until inter-digit timeout, which default is 4 seconds. For example, SPD 1 # + + . 5. Call Screen You may point web browser to your terminal's IP and go to Address Book/Call Screen to configure it. Below illustrates how to configure it by keypad or TELNET. (1) How to activate and deactivate call screen? Main Menu=>1. Address Book/1. Search Locate the target address that you want to screen and press HOLDto choose Go to3. Screen Calland pressHOLD to toggle call screen. (2) List and Revoke Screened Numbers Main Menu=>1. Address Book/5. Call Screening to view all screened addresses. Locate the target address that you want to remove from screening list and press HOLDto choose. Pick 3. Revokeand press HOLDto remove it from the screened list. V. Call Forward You may point web browser to your terminal's IP and go to Call Forwardto configure it. Below illustrates how to configure call forward by keypad or TELNET. AirLive ePhone-2000S -10- English Version 1. Set up forwarding number Main Menu=>4. Call Forward/1. Target Number Press HOLD to pick an entry from address book. Use and to view the current forwarding number. Press MUTEto remove the current mapping of forward number. Note: on incoming calls arrival, both red LED of RejectandForwardfunction keys will be on. If you press Reject which time, the incoming call will be rejected as busy and on recorded as a received call, but it will not be forwarded in anyway. If you would like to transfer it to your configured forwarding number, you should press Forward If you have . not configured the forwarding number, the incoming call will be rejected as busy and recorded as a missed call. 2. Enable Call Forwarding Features (1) All Calls Forward (Unconditionally Forward) Main Menu=>4. Call Forward / 1. All Calls Fwd PickEnabledand pressHOLD to save your setting. Once this feature is enabled, the red LED of Forward function key will flash to remind you that all incoming calls will be silently forwarded to the forwarding number you previously configured (no ringing tone would ever be heard!). If you have not configured the forwarding number, the peer will be replied as "480 Temporarily unavailable" and recorded as a missed call. (2) Busy Forward Main Menu=>4. Call Forward/3. Busy Forward PickEnabledand pressHOLDto save your setting. Once this feature is enabled, the system will start to forward incoming calls to the forwarding number you previously configured when the system is busy (on which time you have already had 2 calls are waiting). If you have not configured such forwarding number, it will reply the peer as busy and recorded as a missed call. (3) No Answer Forward Main Menu 4. Call Forward / 4. No Answer Fwd 1. Status and => / AirLive ePhone-2000S -11- English Version pick Enabled, pressHOLDto save it. Main Menu=>4. Call Forward / 4. No Answer Fwd/ 2. No Answer Time and configure the ringing expiration time before forwarding the incoming , call (system default is ringing for 30 seconds) . Once "forward on no-answer" feature is enabled, if you do not answer the incoming call before the timer expires, it will be forwarded to the forwarding number you previously configured. If you have not configured the forwarding number, the peer will be replied as "no answer" and recorded as a missed call. 3. Do Not Disturb (DND) Press DND function key to toggle this feature: if the red LED is on, this feature is enabled; otherwise it is disabled. When this feature is on, all incoming calls will be silently (no ringing tone will ever be heard) forwarded to the forwarding number you previously configured. [. . . ] Unconditionally auto-answer all incoming calls on idle mode can be achieved by either configuring the global phone-set setting and/or map the auto-answer feature as a programmable key. To configure the global phone-set setting for auto-answer: Press FUNC + # to activate menu. Di s a b l e d . System default is Disabled Note, Web configuration page is Preferences=> "Auto Answer". c. If you have mapped one of your DSS keys to "Auto-Answer", press this DSS to toggle auto-answer mode. [. . . ]