User manual AIRLIVE P-203N

[. . . ] P-203N 3 Ports Wired Print Server User's Manual COPYRIGHT Copyright ©2006/2007 by this company. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of this company. FCC COMPLIANCE STATEMENT This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the authority to operate equipment. DISCLAIMER This company makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular purpose. [. . . ] Bonjour: Allow you to configure the Bonjour function. SNMP Configuration: SNMP Information Configuration. System Configuration: Print Server Network Ability Setting and Firmware Upgrade. Setup Wizard: Guide You Through All the Settings. Report: List the Status of All Available Print Servers on the Network. We will explain each function separately in the following section. 45 AirLive P-203N User's Manual 7. 2 Search for All Available Print Server Every time when you run print server's configuration utility, click the "Search" icon on the tool bar. The configuration utility will delay for several seconds because the utility is using system's available network protocols to search for all print servers on the network. All available print servers will be listed under "Print Server Group" on the left side of the window. You must select the print server you would like to configure from the list. The system will, at the same time, display the selected print server's status on the right side of the window. 46 AirLive P-203N User's Manual 7. 3 Status of Print Server Click "Status" icon on the tool bar, the status of the current selected print server will be showed on the right side of the window. The information of the print server displayed are MAC ID, Model Type, Firmware Version, status of each printer port, NetWare file server name, NetWare file server polling interval, NetWare printer queue names, IP address, subnet mask, default gateway, AppleTalk printer type, AppleTalk zone and print server printing ability. . . etc. You can refresh the print server's status by pressing the "Refresh" button . You can restart the print server by pressing the "Reboot" button . 47 AirLive P-203N User's Manual 7. 4 Setup the Print Server Click "Setup" icon on the tool bar, the setup items of the current selected print server will be showed on the right side of the window. Double click one of the icons to set up the selected print server. A screen will pop up to verify "User Name" and "Password" of the print server. The default values are as follows. User Name: admin Password: airlive 48 AirLive P-203N User's Manual 7. 5 General Configuration Double Click "General" icon and the General configuration window will pop-up. You can see basic print server information in this page. You also can configure the "Print Server Name", "SMB Group Name", "User Name" and "Password" here. Server Name, the name of the print server. You can use this name to identify the print server when you are searching for the print server by the administration and client utilities. User Name / Password is used to authenticate the administrator by the Web administration tool. 49 AirLive P-203N User's Manual 7. 6 TCP/IP Configuration Double Click "TCP/IP" icon and the TCP/IP configuration window will pop-up. You can configure the print server to automatically get IP from DHCP server or manually specify static IP. The print server also has a built-in DHCP server. [. . . ] LPR Printing can be set up on any Macintosh with version 9. x above. To enable LPR Printing in Macintosh, please follow the procedures below. In the Desktop, click "System Preferences". Step2. Click "Print & Fax". Step3. From the "Print & Fax" screen, click "Set Up Printers. . . ". 101 AirLive P-203N User's Manual Step4. Click "Add" to add the new Print Server through TCP/IP. Step5. Enter the "Printer Type", "Printer Address" and "Queue Name" and select the "Printer Model" to setup the Print Server. [. . . ]