User manual AIRTRONICS SD-6G

[. . . ] Page 1 TaBLE OF cOnTEnTS Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 3 Additional Receiver Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 3 Transmitter Signal Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 3 FCC Compliance Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The cursor will default to FL 4LA>0%. Page 40 aERO MODEL TyPE Choosing the Flight Mode - Common or Separate, Continued. . . . 3) Press the Navigation Pad 5 to move the cursor to F-MODE>COMMON. 4) Press the INC+/M1 or DEC-/M2 keys to choose either SEPARATE or COMMON. 5) If you choose SEPARATE, press the F-MODE key to choose the F-MODE number you would like to program the Flaperon Mixing function for. Changing Flaperon Mixing Percentage Values AERO MODEL TYPE IMPORTANT Adjusting the Flaperon4Left Aileron and Flaperon4Right Aileron percentage values changes the percentage of Flaperon travel in relation to the Flap channel End Point Adjustment percentage value. For example, if the Flap Switch '1' End Point Adjustment percentage value is set to 100% and the Flaperons move down 2", changing the Flaperon4Left Aileron and Flaperon4Right Aileron percentage values to 50% will cause the Flaperons to move down 1". In addition, changing the Flaperon4Left Aileron and Flaperon4Right Aileron percentage values to -50% will cause the Flaperons to move up 1" (Spoilerons). 1) Press the Navigation Pad 6 to highlight FL4LA>0%, then press the INC+/M1 or DEC-/M2 keys to change the Flaperon4Left Aileron Mixing percentage value. 2) Press the Navigation Pad 6 to highlight FL4RA>0%, then press the INC+/M1 or DEC-/M2 keys to change the Flaperon4Right Aileron Mixing percentage value. FLAPERON setting range is -100% to 100%. When the percentage value is increased from 0% to 100%, Flaperon travel will increase in one direction. When the percentage value is decreased from 0% to -100%, Flaperon travel will increase in the opposite direction. 17. FL4EL (FLaP TO ELEvaTOR MiXing) The Flap to Elevator Mixing function allows you to mix a percentage of elevator control with flap control. When you move the flaps up and down, the elevator will move up and down. The Flap to Elevator Mixing function is typically used to reduce the ballooning tendency that most aircraft exhibit when the flaps are lowered. The amount and the direction that the elevator moves with flap control is adjusted by changing the Flap to Elevator mixing percentage value either positive or negative. For greater flexibility, the Flap to Elevator Mixing function can be programmed either the same for all Flight Modes or separately for each of the three Flight Modes. In the majority of cases, you will want to program the Flap to Elevator Mixing function to move the elevator down enough to minimize ballooning when the flaps are lowered. Transmitter F-MODE Programming F-MODE Transmitter F-MODE refers to the Flight Mode that the transmitter is currently operating in. Programming F-MODE refers to the Flight Mode that you would like to change the programming for. Page 41 aERO MODEL TyPE 17. FL4EL (FLaP TO ELEvaTOR MiXing), cOnTinUED. . . . Choosing the Flight Mode - Common or Separate 1) From the Display screen, press the ENTER key to display the Programming Menus. 2) Press the Navigation Pad 56 to highlight FL 4EL, then press the ENTER key to display the FL 4EL menu. The cursor will default to FL 4EL>0%. 3) Press the Navigation Pad 5 to move the cursor to F-MODE>COMMON. 4) Press the INC+/M1 or DEC-/M2 keys to choose either SEPARATE or COMMON. 5) If you choose SEPARATE, press the F-MODE key to choose the F-MODE number you would like to program the Flap to Elevator Mixing function for. Changing Flap to Elevator Mixing Percentage Values The channel options displayed will differ based on the Model Type selection options you chose previously. For example, if you chose TAIL>2xEL in the TYPE menu, FL4LE (Left Elevator) and FL4RE (Right Elevator) percentage values can be changed separately. 1) Press the Navigation Pad 6 to highlight FL4EL>0%, then press the INC+/M1 or DEC-/M2 keys to change the Flap 4 Elevator Mixing percentage value. [. . . ] See Ailvator Mixing, Programming Mixing, CCPM Swashplate Options 55, 56 Mixing, Delta. See Delta Mixing End Point Adjustment, Programming Mixing, Dual Elevator. See Dual Elevator Mixing End Point Adjustment, Programming Mixing, Elevator to Flaperon/Spoileron - Compensation Mixing Example 50 Mixing, Flap to Elevator. See Flap to Elevator Mixing, Programming Mixing, Flaperon. [. . . ]