User manual AKAI ATE-22Y101

[. . . ] This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference will not occur in a particular installation. If this equipment does cause by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. [. . . ] The power indicator changes from red to green. - Press the POWER on the remote control or on the control panel again to return the display to standby mode. The power indicator changes from green to red. Note: For protecting your LCD TV product, the interval time between turn on the LCD TV product and shut down it should be kept at least one minute. POWER SOURCE 6. 2 Selection of Input Mode , ENTER - Press SOURCE / on the remote control or on the LCD TV control panel to select the signal source you desired. ADD/EARSE FAVORITE When no input from the selected signal source, "Main no signal" and blue background on the will appear, press SOURCE / remote control or on the control panel again to search the next source. Note: The LCD-TV will automatically turn itself off after approximately 15 minutes if no signal input. When no signal is inputed for about 14 minutes. A "No signal and going to power down" wording will appear. You can press "" or "" button to selected, press "ENTER" to confirm. If select "Cancel" or no operation, the LCD-TV will automatically turn off after 1 minutes, if select "OK", it will turn off immediately. 6. 3 Other Function - FAVORITE: Press FAVORITE button repeatedly, you will cycle through Favorite Channel. ADD/ERASE: Press this button to add/erase current channel to/from the list of favorite directly. Add current channel into the list of favorite if a heart shape mark displaying on the left top of screen. Erase current channel from the list of favorite if a broken heart shape mark displaying. The OSD menu displayed in the following sequence (circular display): Video Audio Misc TV Geometric (Continued on next page) 20 Press MENU to display the menu system. Press ENTER on the remote control or SOURCE on the TV control panel to activate the function settings in the menu. Press , , , to select or adjust a setting, press ENTER to confirm. If you do not make a selection within 15 seconds, the main menu closes automatically; the other menus close automatically within 6 seconds. To close an on-screen menu instantly, press MENU on the remote control or MENU on the control panel. SOURCE ENTER MENU TV control panel CH. SOURCE MENU VOL. STANDBY SOURCE MENU 6. 6 OSD Functions 1 Using the Video Menu Option Contrast Brightness Back Light Saturation Hue Sharpness Phase Color Temperature Advanced Picture Adjust Note: Press / 0~100 0~100 Bright, Middle, Dark 0~100 -30~+30 0~7 0~31 Cool, Middle, Warm, User Description Reduce/Enhance Darken/Brighten Adjust the balance of back light Decrease/Increase of color Decrease/Increase Soften/Sharpen Decrease/Increase Adjust the balance of whitening Adjust the picture effect Video Menu is just for TV, AV, S-Video, Component 1 and Component 2 input source mode. It is not available in other input source mode. Contrast, Brightness, Saturation, Hue, Sharpness can be adjusted only if picture mode is in USER mode. When smart picture mode is pre-set, the value of the above settings will be different according to different input source. (Continued on next page) 21 OSD FUNCTIONS----VIDEO MENU Adjustment of "Contrast" Press MENU on the remote control, and then press or until the "Video" menu appears. Press "ENTER" to confirm and display a status bar as below. Press to decrease that will soften the color. Press "ENTER" to confirm the adjustment and return. [. . . ] Wipe the display with a dry cloth after cleaning. 4 Simple Troubleshooting: If the display fails or the performance changes dramatically, check the Display in accordance with the following instructions. Remember to check the peripherals to pinpoint the source of the failure. If the Display still fails to perform as expected, contact the dealer for assistance. [. . . ]