User manual AKAI LCT2715

[. . . ] Safety Guidelines Caution: Always use a power cable is properly grounded. Please use the AC cords listed below for each area: USA . . . . . . . . . . . . . . . . . . . . . . CSA/cUL FCC Information This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. [. . . ] To display a TV broadcast in the POP window: 1. Press PIP button to enter the POP window. Press PIP for selecting the different PIP modes, such as following; Normal Picture PIP SOURCE Basic PIP Mode LR POP Mode Use / to select the window and active it with a red-colored frame. Press SOURCE to select the input source for the POP window. To change the next programmed channels, press number buttons (0~9) or CH+/CH-. Note: a. If the V-CHIP feature is active and you try to watch a TV program that exceeds your set rating limits, the program will be blocked. For active window, you can change channels, adjust volume, select input source ect. . After power off, the active window will be keep the setting when you power on next time. It is must to have second video source connected for basic PIP and L/R POP modes. After you choose the POP mode, all settings are only aimed at the active window. (Continued on next page) 19 USING THE POP DOUBLE-WINDOW FEATURE OSD OPTION ADJUSTMENT OSD FUNCTIONS To display a picture from an external source in the POP window: 1. (refer to Connect Accessory Devices page). Select the TV program you want to watch in the main window. Repeatedly press SOURCE to select the input source for the POP window. To change the PIP picture size: Press PIP SIZE button to select the PIP picture size, such as: Small, Middle, Large. To change the PIP position: Press PIP POS button to change the PIP window position under PIP mode, it display as following; Right Down Left Down Left Up Right Up Right Down PIP SIZE PIP POS Left Up Right Up ENTER Left Down Right Down Switching the pictures: When in Basic PIP mode, press "ENTER" to swap main or sub pictures; When in LR POP mode, press "ENTER" swap the L/R pictures. When the red frame is displaying in main window, the sound goes out of main window source. If it display in sub window, the sound goes out of sub window source. To change Main or Sub sound: 6. 5 OSD Option Adjustment Learning about the menu system After you have installed the batteries and programmed the remote control, you will need to set some preferences on the TV using the menu system. You can access the menu using the buttons on your TV or remote control. The OSD menu displayed in the following sequence (circular display): Video Audio Misc TV Geometric (Continued on next page) 20 Press MENU to display the menu system. Press ENTER on the remote control or SOURCE on the TV control panel to activate the function settings in the menu. Press , , , to select or adjust a setting, press ENTER to confirm. If you do not make a selection within 15 seconds, the main menu closes automatically; the other menus close automatically within 6 seconds. To close an on-screen menu instantly, press MENU on the remote control or MENU on the control panel. SOURCE ENTER MENU TV control panel CH. SOURCE MENU VOL. STANDBY SOURCE MENU 6. 6 OSD Functions 1 Using the Video Menu Option Contrast Brightness Back Light Saturation Hue Sharpness Phase Color Temperature Advanced Picture Adjust Note: Press / 0~100 0~100 Bright, Middle, Dark 0~100 -30~+30 0~7 0~31 Cool, Middle, Warm, User Description Reduce/Enhance Darken/Brighten Adjust the balance of back light Decrease/Increase of color Decrease/Increase Soften/Sharpen Decrease/Increase Adjust the balance of whitening Adjust the picture effect Video Menu is just for TV, AV, S-Video, Component 1 and Component 2 input source mode. It is not available in other input source mode. [. . . ] (Continued on next page) 46 Symptom Power cannot be turned on. (Power indicator does not light) No Input Signal message appears. Solution - Check that both ends of the power cable are plugged into the socket appropriately. - Check that the signal line is connected properly. - Check that the power of the relevant peripherals is turned on. [. . . ]