User manual AKAI PT-5250A

[. . . ] PROJECTION TELEVISION BP68-00516A-01 (P62A_Akai_Eng) PT4250A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT5250A . . . . . . . . . . . . . Owner's Instructions 7/5/05 1:08 PM Page 1 BP68-00516A-01 (P62A_Akai_Eng) 7/5/05 1:08 PM Page 2 BP68-00516A-01 (P62A_Akai_Eng) 7/5/05 1:08 PM Page 3 Warning!Important Safety Instructions CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. [. . . ] Air Cable Air + Cable Start Start Start oe Air : "Air" antenna signal Cable : "Cable" antenna signal Air+Cable : "Air" and "Cable" antenna signals When selecting Cable TV system: Press the or button to select "Cable", then press the ENTER button. Press the or button to select "STD", "HRC" or "IRC", then press the ENTER button. TV Auto Program Select the antennas to memorize. Air Cable Air + Cable Start Start Start oe STD, HRC and IRC TV Auto Program Select the cable system. STD HRC IRC identify various types of cable TV systems. Contact your local cable company to identify the type of cable system that exists in your particular area. At this point the signal source has been selected. Proceed to "Storing Channels in Memory". Storing Channels in Memory 5 Press the or button to select the antennas to memorize. Press the ENTER button to select "Start". TV Auto Program Select the antennas to memorize. Air Cable Air + Cable Start Start Start 6 Press the ENTER button to start the auto program. The TV begins memorizing all available channels. Press the ENTER button at any time to interrupt the memorization process. Press the EXIT button to exit. Auto Program Auto Program in Progress. Air Channel 15 Stop oe The TV must be connected to an antenna in order to receive digital TV signals. Even if a particular channel is deleted from memory, you can always tune to that channel directly by using the number buttons on the remote control. · All available DTV and analog channels are automatically stored in memory when channels are selected by the direct tuning function. English - 37 BP68-00516A-01 (P62A_Akai_Eng) 7/5/05 1:09 PM Page 38 O P E R AT I O N Adding and Erasing Channels To add channels that were not memorized (or to delete unwanted channels from memory): 1 Press the MENU button. Press the or button to select "Channel", then press the ENTER button. TV Channel Antenna : Air Auto Program Add / Delete Favorite Channels Name Fine Tune More 2 Press the or button to select "Add/Delete", then press the ENTER button. TV Channel Antenna : Air Auto Program Add / Delete Favorite Channels Name Fine Tune More 3 Repeatedly pressing the ENTER button will alternate between add channel and delete channel. Press the CH or CH button to switch to the appropriate channel, then repeat above. Add / Delete Air 11 Not In Memory Add Press ENTER to add the channel. <Add channel> Add / Delete Press the EXIT button to exit. Air 11 In Memory Delete Press ENTER to delete the channel. <Delete channel> Alternate method: Simply press the ADD/DEL and ENTER buttons on the remote control to add channels that were not memorized or to delete unwanted channels from memory. Add / Delete Air 11 Not In Memory Add Press ENTER to add the channel. English - 38 BP68-00516A-01 (P62A_Akai_Eng) 7/5/05 1:09 PM Page 39 O P E R AT I O N Changing Channels Using the Channel Buttons Press the CH or CH button to change channels. When you press the CH or CH button, the TV changes channels in sequence. You will see all the channels that the TV has memorized. (The TV must have memorized at least three channels. ) You will not see channels that were either erased or not memorized. Using the Number Buttons Use the number buttons to quickly tune to any channel. Press the number buttons to go directly to a channel. For example, to select channel 27, press "2, " then "7. " The TV will change channels when you press the second number. Using the "-" Button The "-" button is used to select channels that broadcast both a digital and analog signal. For example, for Channel 7 (digital), press "7", then "-", then "1" and you will see as left. DTV Cable 7-1 KYW-HD HD For channel 7-2 (analog), press "7", then "-", then "2" and you will see as left. DTV Cable 7-2 R SD Multi Note · HD indicates the TV is receiving a digital High Definition signal. SD indicates the TV is receiving a analog Standard Definition signal. Using the Previous Channel Press the PRE-CH button. The TV changes to the last channel you were watching. PRE-CH FAV. CH CH. [. . . ] If you are using a VCR, check the tracking. Unplug the TV for 30 seconds, then try operating it again. Press the MODE button to put your remote control in the "TV" mode. Please check the digital signal strength and input antenna. [. . . ]