User manual ALCATEL-LUCENT 546 1

[. . . ] SpeedTouch TM 516/536/546/510v5/530v5 Multi-User ADSL Gateways CLI Reference Guide Release R5. 2. 7 SpeedTouch TM 516/536/546 510v5/530v5 CLI Reference Guide R5. 2. 7 Copyright Copyright ©1999-2004 THOMSON. Passing on, and copying of this document, use and communication of its contents is not permitted without written authorization from THOMSON. The content of this document is furnished for informational use only, may be subject to change without notice, and should not be construed as a commitment by THOMSON. THOMSON assumes no responsibility or liability for any errors or inaccuracies that may appear in this document. [. . . ] Choose between: input: The point of all incoming traffic. At this point, it can be determined whether the packet is allowed to reach the SpeedTouchTM IP router or local host. sink: The point of all traffic destined to the SpeedTouchTM IP router itself. At this point, it can be determined whether the packet is allowed to address the local host. forward: The point of all traffic to be forwarded by the SpeedTouchTM IP router. At this point, it can be determined whether the packet is allowed to be handled, i. e. source: The point of all traffic sourced by the SpeedTouchTM IP router. At this point, it can be determined whether the packet is allowed to leave the local host. output: The point of all outgoing traffic. At this point, it can be determined whether the packet is allowed to leave the SpeedTouchTM IP router or local host. REQUIRED REQUIRED EXAMPLE: =>firewall assign assign assign =>firewall =>firewall =>firewall assign assign assign => list hook=sink chain=sink hook=forward chain=forward hook=source chain=source chain create chain=Telnet assign hook=sink chain=Telnet list hook=sink chain=Telnet hook=forward chain=forward hook=source chain=source RELATED COMMANDS: firewall list firewall unassign Show the association(s) between all hooks or a specified hook and their chain(s). Clear a specific hook. 154 E-DOC-CTC-20040907-0010 v1. 0 Firewall Commands firewall flush Clear all the hooks, chains and rules. The flush command does not impact previously saved configurations. SYNTAX: firewall flush EXAMPLE: =>firewall =>firewall assign assign assign =>firewall =>firewall assign assign =>firewall =>firewall => load list hook=sink hook=forward hook=source flush hook=sink list hook=forward hook=source flush list chain=sink chain=forward chain=source chain=forward chain=source E-DOC-CTC-20040907-0010 v1. 0 155 Firewall Commands firewall list Show the association(s) between all hooks or a specified hook and their chain(s). SYNTAX: firewall list where: hook The name of the hook for which the associations must be shown. Choose between: input sink forward source output. OPTIONAL [hook = <{input | sink | forward | source | output}>] Note If not specified, the associations for all hooks are shown. EXAMPLE: =>firewall list firewall assign firewall assign firewall assign firewall assign firewall assign =>firewall list firewall assign =>firewall list firewall assign => hook=input chain=None hook=sink chain=sink hook=forward chain=forward hook=source chain=source hook=output chain=None hook=input hook=input chain=None hook=forward hook=forward chain=forward RELATED COMMANDS: firewall assign firewall unassign Assign a chain to an entry point. Clear a specific hook. 156 E-DOC-CTC-20040907-0010 v1. 0 Firewall Commands firewall troff Disable verbose console messaging. SYNTAX: firewall troff EXAMPLE: =>firewall troff RELATED COMMANDS: firewall tron Enable verbose console messaging. E-DOC-CTC-20040907-0010 v1. 0 157 Firewall Commands firewall tron Enable verbose console messaging. SYNTAX: firewall tron EXAMPLE: =>firewall tron RELATED COMMANDS: firewall troff Disable verbose console messaging. 158 E-DOC-CTC-20040907-0010 v1. 0 Firewall Commands firewall unassign Clear a specific hook. SYNTAX: firewall unassign where: hook The name of the hook to be cleared. Choose between: input sink forward source output. REQUIRED hook = <{input | sink | forward | source | output}> RELATED COMMANDS: firewall assign firewall list Assign a chain to an entry point. Show the association(s) between all hooks or a specified hook and their chain(s). E-DOC-CTC-20040907-0010 v1. 0 159 Firewall Commands firewall chain create Create a new chain. SYNTAX: firewall chain create where: chain The name of the chain to be created. REQUIRED chain = <string> EXAMPLE: =>firewall chain list Tempo, source, forward, sink =>firewall chain create chain=Telnet =>firewall chain list Telnet, Tempo, source, forward, sink => RELATED COMMANDS: firewall chain delete firewall chain list Delete a chain. Show a list of all current chains. 160 E-DOC-CTC-20040907-0010 v1. 0 Firewall Commands firewall chain delete Delete a chain. SYNTAX: firewall chain delete where: chain The name of the chain to be deleted. REQUIRED chain = <string> EXAMPLE: =>firewall chain list Telnet, Tempo, source, forward, sink =>firewall chain list Telnet, Tempo, source, forward, sink =>firewall chain delete chain=Tempo =>firewall chain list Telnet, source, forward, sink => RELATED COMMANDS: firewall chain create firewall chain list Create a new chain. [. . . ] OPTIONAL Specify the lowest priority severity of the syslog messages to be shown. Only the messages with a severity as specified or higher will be shown. Use one of the supported severity names (see " Supported Syslog Severities" on page 380). Note hist If not specified, the messages of all the facilities will be shown. OPTIONAL Show messages over several SpeedTouchTM reboots (yes) or show only messages since latest startup (no). Note dest If not specified, only the recent messages will be shown. [. . . ]