User manual ALCATEL-LUCENT 570

[. . . ] SpeedTouchTM 545/570 Multi-User ADSL Gateways Setup and User's Guide Release R4. 2. 1 500 SERIES SpeedTouchTM 545/570 Setup and User's Guide Release R4. 2. 1 Status Change Note Short Title Copyright v1. 0 PeckelbeenS Setup and User's Guide ST545/570 R4. 2. 1 (en) © 2003 THOMSON. Passing on, and copying of this document, use and communication of its contents is not permitted without written authorization from THOMSON. The content of this document is furnished for informational use only, may be subject to change without notice, and should not be construed as a commitment by THOMSON. THOMSON assumes no responsibility or liability for any errors or inaccuracies that may appear in this document. Contents 1 1. 1 1. 2 1. 3 1. 3. 1 1. 3. 2 SpeedTouchTM Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] For enhanced security, after going through the SpeedTouchTM configuration setup procedures, you are able to "personalize" the SpeedTouchTM wireless access point settings by configuring another SSID, and/or optionally another security level. For more information on the configuration of the SpeedTouchTM Wireless configuration, see " Wireless" on page 52. Preconditions Make sure that: · · · · · · · The SpeedTouchTM is powered on and ready for service. The SpeedTouchTM has been configured by the SpeedTouchTM Setup wizard or via uploading the appropriate configuration profile file. Optionally, the SpeedTouchTM wireless settings have been personalized. The wireless client adapters are installed on the computers you want to connect. In case WEP encryption is enabled on the SpeedTouchTM, you must configure the wireless client to use the same encryption level and WEP key. In case SSID broadcasting is disabled, you must configure the wireless client for the SpeedTouchTM SSID. Depending on the registration button and Access Control List configuration: · In case registration is disabled and the Access Control List unlocked, no further actions are needed for the wireless client to access the SpeedTouchTM WLAN. In case registration is disabled and the Access Control List locked, you must manually add the wireless client to the Access Control List as described in " Wireless" on page 52. Make sure to save your SpeedTouchTM configuration by clicking Save all. In case registration is enabled and the Access Control List locked, you must follow the procedure below to register the WLAN client to the SpeedTouchTM Access Control List. Further make sure that: Depending on the personalized wireless settings: · · E-DOC-CTC-20030814-0001 v1. 0 45 4 Wireless Connectivity Registering wireless clients In case registration is enabled, you must register pending wireless network clients as follows: 1 Make sure the wireless client is correctly associated to the SpeedTouchTM WLAN. Depending on your WLAN client adapter a wireless icon may become green or a message similar to the following may appear: "Successfully joined Wireless network SpeedTouch012345". Note Some WLAN clients do not automatically join a WLAN. If so, follow the instructions for the WLAN client software to initiate the association. 2 Push the red Registration button on the SpeedTouchTM back panel or click Register on the SpeedTouchTM Wireless web page (see " Wireless" on page 52 for more information). The SpeedTouchTM will now add the wireless client to the Access Control List and save the current configuration. Note You can only register one wireless client at a time. So you have to push the registration button for each client you want to add. 3 Browse to the SpeedTouchTM Wireless web page to see that the MAC address of your wireless client is added to the Access Control List. Note If a system password secures the SpeedTouchTM from unauthorized access, you'll need to authenticate first before you can actually browse its web pages. 46 E-DOC-CTC-20030814-0001 v1. 0 5 SpeedTouchTM Web Interface 5 SpeedTouchTM Web Interface Introduction The SpeedTouchTM comes with integrated local configuration capabilities. The local configuration, via the SpeedTouchTM web interface, is based on the HTTP server/web browser concept. It allows you to configure your SpeedTouchTM via a web browser using HTML pages from any local computer attached to the SpeedTouchTM (Wireless) LAN. Preconditions Before accessing the SpeedTouchTM web pages, make sure that either: · · Your Web browser is not using a proxy server. [. . . ] Make sure the power switch on the SpeedTouchTM is turned on. Wireless client can not participate in the SpeedTouchTM wireless network. In case registration is enabled, you must press the 'Registration' button to register the wireless client. Make sure that the SpeedTouchTM Association Control List is not locked, i. e. [. . . ]