User manual ALCATEL-LUCENT 608 WL

[. . . ] SpeedTouchTM 605/608/608 WL/620 (Wireless) Business DSL Routers User's Guide Release R5. 3. 1 SpeedTouchTM608WL and SpeedTouchTM620 only SpeedTouchTM 605/608 608 WL/620 User's Guide R5. 3. 1 Copyright Copyright ©1999-2005 THOMSON. Passing on, and copying of this document, use and communication of its contents is not permitted without written authorization from THOMSON. The content of this document is furnished for informational use only, may be subject to change without notice, and should not be construed as a commitment by THOMSON. THOMSON assumes no responsibility or liability for any errors or inaccuracies that may appear in this document. [. . . ] Select a service to: View detailed SpeedTouchTM service information. Generally it is advised not to alter any of the settings of a SpeedTouchTM service. ! E-DOC-CTC-20050429-0104 v1. 0 115 Chapter 5 Expert Configuration Edit SpeedTouchTM service properties Editing SpeedTouchTM services might be useful in cases where you want to hide/ protect the service by deviation from the typical service settings or restricting access from/to interfaces. However; ! 1 2 Do not edit SpeedTouchTM system services unless specifically needed. To edit a SpeedTouchTM system service: Select the service. In Service properties: Select or clear Service enabled to respectively enable or disable the service. Depending on the service, either: Select a Source IP interface. Type a new Internal TCP/UDP port. 3 In External TCP/UDP Port, optionally: Clear existing External TCP/UDP ports, if applicable. Type the port number of an additional external TCP/UDP port to add. 4 In Allow service via (Interface), optionally: Clear existing interfaces, if applicable. Type the name of the additional interface. 5 In Accept service from (Remote IP), optionally: Clear existing remote IP addresses, if applicable. Type the IP address of the specific remote IP host. 6 Click Apply to apply your changes to the SpeedTouchTM service. You must repeat the procedure for each individual External TCP/UDP port, interface, or remote IP address you want to add. 116 E-DOC-CTC-20050429-0104 v1. 0 Chapter 5 Expert Configuration SpeedTouchTM service types The SpeedTouchTM service can be of following type: Type Client Server Peer Proxy Relay Indicates a SpeedTouchTM service that. . . is the originator of an IP connection (source IP packets). is the responder of an IP connection (listening to IP packets). can be an originator or a responder of an IP connection. is a responder on the LAN side and originator on the WAN side of the SpeedTouchTM. is a responder on one side (LAN or WAN) and reoriginates on the other side (WAN resp. is an assembly of SpeedTouchTM services. Editing such kind of entries will edit all members of that Group. has been dynamically created or enabled by the SpeedTouchTM service manager. the service is member of a SpeedTouchTM Group service. uses a protocol port as another existing SpeedTouchTM service. Group Transparent-Map Dynamic Sibling Shared E-DOC-CTC-20050429-0104 v1. 0 117 Chapter 5 Expert Configuration 5. 2. 8 SNTP Overview The Simple Network Time Protocol (SNTP) web page allows you to configure the SpeedTouchTM real-time clock. The page contains two sections: SNTP Client Manual Selecting Manual immediately disables the SpeedTouchTM SNTP client. As a consequence the SpeedTouchTM real-time clock will no longer be periodically synchronised with an Internet time server. ! SNTP Client As long as the SNTP section is selected, automatic time synchronisation of the SpeedTouchTM real-time clock by means of the SpeedTouchTM SNTP client is guaranteed (given that NTP servers are configured of course). The SNTP table allows you to overview and add/delete NTP servers (present on the Internet or your local network) to which the SpeedTouchTM real-time clock is able to synchronize its time settings with. To add an NTP server: 1 2 Click New (if an entry is currently selected, click Cancel first) Type the host name or IP address of the NTP server. [. . . ] Proceed as follows: 1 2 3 4 On the Start menu, click (Settings >) Control Panel. In the Add or Remove Programs window appears, click Add/Remove Windows Components. In the Windows Components Wizard, select Networking Services in the Components list and click Details. 5 In the Networking Services window, select Universal Plug and Play or UPnP User Interface and click OK. 6 7 Click Next to start the installation and follow the instructions in the Windows Components Wizard. At the end of the procedure the wizard prompts you that the installation was successful. [. . . ]