User manual ALCATEL-LUCENT OMNIACCES-VOIP GATEWAY

[. . . ] C April 2004 VoIP User Manual Release 4. 5 An Alcatel service agreement brings your company the assurance of 7x24 no-excuses technical support. You'll also receive regular software updates to maintain and maximize your Alcatel product's features and functionality and on-site hardware replacement through our global network of highly qualified service delivery partners. Additionally, with 24-hour-a-day access to Alcatel's Service and Support web page, you'll be able to view and update any case (open or closed) that you have reported to Alcatel's technical support, open a new case or access helpful release notes, technical bulletins, and manuals. For more information on Alcatel's Service Programs, see our web page at www. ind. alcatel. com, call us at 1-800-995-2696, or email us at support@ind. alcatel. com. This manual documents Release 4. 5 Voice over IP (VoIP) hardware and software. [. . . ] Default: For E1 ISDN PRI, the default channel values are 1-15, 17-31. For BRI Euro, the default channel values are is 1-2. Command Example: voice channel 2/1 1 isdn b channel voice channel 2/2 2 isdn b channel voice channel 3/1 1 isdn b channel voice channel 3/2 15 isdn b channel voice channel 3/3 17 isdn b channel voice channel 3/4 31 isdn b channel Remarks The voice port isdn connection switch type command is used to configure the type of switch connection for the ISDN ports at the voice daughtercard level. Specification of the ISDN protocol is optional if not using E1 ISDN PRI or BRI Euro. Use the table and illustration above to determine valid bearer/data channel, slot and port values (applies to OS/R with two voice switching daughtercards). Page 5-57 VoIP Commands Channel Properties The commands listed and described below are used to configure the channel properties for individual voice channels as follows: voice channel mode, PLAR (Private Line Automatic Ringdown), outbound caller ID, and voice channel initialization. Voice Channel Configuration voice channel mode voice channel PLAR dial-in phone number Channel Operational State voice channel initialization (in-service/out-of-service) Page 5-58 VoIP Commands voice channel mode Command Usage Specify voice channel mode--telephony, passthrough or PLAR (Private Line Automatic Ringdown) used to complete calls on designated channels. Establishes semi-fixed bandwidth connections between points in the network. Syntax Options voice channel <slot/port/startChannel-endChannel > mode {telephony | pass through | plar} Definitions: slot port startChannel endChannel Specifies slot number of voice daughtercard installed in switching module, (e. g. , 2). Specifies physical port number on voice daughtercard, (e. g. , 2). The first number in the range of voice channels (e. g. , 1). The last number in the range of voice channels (e. g. , 30). o Syntax Note o Be sure to separate the start and end range numbers with a hyphen (e. g. , 1-30). telephony pass through Allows use of Numbering Plan to complete calls to specified hunted destination. Allows two DS-0 channels to be cross-connected to complete calls (not available this release) Allows calls to be routed based upon telephone number configured to dialing plan. plar Default: The default setting is telephony. Command Examples: voice channel 2/2/1-12 mode telephony voice channel 2/2/13-24 mode pass through voice channel 2/2/1-12 mode plar Remarks In the telephony mode, digits come from voice path or signaling. Upon in-seize, the voice switching daughtercard collects inbound digits, then uses the Numbering Plan to complete calls to the specified hunted destination. In the passthrough mode, no digit processing is performed by the DSPs on the voice switching daughtercard, and no routing is performed. Upon in-seize, the channel is immediately connected to another channel, via Numbering Plan processing. In the PLAR mode, no inbound digit processing takes place. Upon in-seize, the PLAR telephone number is immediately routed based upon the dialing plan. The telephone number must be configured to automatically dial using the dial plan. Page 5-59 VoIP Commands voice channel dial in private line automatic ringdown Command Usage Specify voice channel Private Line Automatic Ringdown (PLAR) dial-in phone number. This command is used to configure the number to be dialed in Switched CAS mode when a specified channel goes off-hook. Syntax Options voice channel <slot/port/startChannel-endChannel > dial in private line automatic ringdown <"plar phone number" > Definitions: slot port startChannel endChannel Specifies slot number of voice daughtercard installed in switching module, (e. g. , 2). Specifies physical port number on voice daughtercard, (e. g. , 2). [. . . ] Specifies port channel number range in which to reset DSP receive and transmit statistics, (e. g. , 1-12); cumulative for the current call on specified channel. Type either stats or statistics in the command line. o Syntax Notes o This command only works from within the command line interface, and cannot be used from within the vsmboot. asc file. Default: None Command Example: voice channel 2/1/1-12 reset dsp statistics voice channel 2/1/13-24 reset dsp stats Page 5-277 VoIP Commands voice channel reset error stats Command Usage Reset error statistics for one or more voice channels. (Not available this release. ) Syntax Options voice channel <slot/port/startChannel-endChannel > reset error stat[istic]s Definitions: slot port channel istic Specifies chassis slot number where VSM is installed, (e. g. , 2). [. . . ]