User manual ALCATEL-LUCENT OMNIACCESS 4308

[. . . ] OmniAccess 4308 TM Wireless LAN Switch Installation Guide i OmniAccess 4308: Installation Guide Copyright Copyright © 2005 Alcatel Internetworking, Inc. Specifications in this manual are subject to change without notice. Originated in the USA. Trademarks Alcatel®, the Alcatel logo, AOS-W, and OmniAccess, and the OmniAccess 4308 are trademarks of Alcatel in the United States and certain other countries. Any other trademarks appearing in this manual are owned by their respective companies. ii Part 031638-00 May 2005 Electromagnetic Interference FCC - Class A This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. [. . . ] Remove all rings, jewelry, and other potentially conductive material before working with this product. Never insert foreign objects into the chassis or any other component, even when the Alcatel Wireless LAN Switch is unpowered or unplugged. Main power is fully disconnected from the Alcatel Wireless LAN Switch by unplugging the power cord from the power outlet. For safety reasons, verify the power outlet and plug are within easy reach of the operator. Do not handle electrical cables which are not insulated. To minimize electrical hazard, keep water and other fluids away from the product. Comply with electrical grounding standards during all phases of installation and operation of the product. Do not allow the Alcatel Wireless LAN Switch chassis, network ports, power source, or mounting brackets to contact any device, cable, object, or person attached to a different electrical ground. Also, never connect the device to external storm grounding sources. Installation or removal of the chassis must be performed in a static-free environment. The proper use of anti-static body straps and mats is strongly recommended. Do not ship or store this product near strong electromagnetic, electrostatic, magnetic, or radioactive fields. This product has no internal serviceable parts. When service or repair is needed, see "Contacting Alcatel" on page ix. 6 Part 031638-00 May 2005 Chapter 2 Requirements Rack Mounting Kit Using the included rack mounting kit, you can mount the Alcatel Wireless LAN Switch in a standard 19-inch network equipment rack. The rack mounting kit contains the following parts: 6-32 Flat Head Screws x6 12-24 Screws Left Bracket Right Bracket x4 FIGURE 2-1 Rack Mounting Kit NOTE--The four 12-24 screws are intended for securing the switch to the rack. Some racks require different screws which are not included. Make sure that you have the correct screws or fasteners for your rack system before attempting to mount the switch. Installing the Chassis 7 OmniAccess 4308: Installation Guide Selecting a Location The Alcatel Wireless LAN Switch, like other network and computing devices, requires an "electronics friendly" environment. Reliable power Make sure that your electrical outlet is compatible with the Alcatel Wireless LAN Switch. The switch power input is auto-ranging and accepts 90~132/180~264 VAC, 50 to 60 Hz, 3. 5/2. 0 A. The power cords must be rated to 10 A and conform to grounded electrical standards in the country where the product is operated. Use of a power line conditioner or Uninterruptible Power Supply (UPS) can decrease or mitigate problems caused by power service fluctuations. Make sure that the output of any power shaping device is compatible with the Alcatel Wireless LAN Switch power supply. Cool, non-condensing ventilation For proper operation, the Alcatel Wireless LAN Switch requires an environment with an ambient air temperature between 0 to 40 ºC (32 to 104 ºF). Humidity must be kept at non-condensing levels between 5 and 95%. [. . . ] A straight-through cable is required to preserve POE voltage polarity. The port should be connected to the intended device either directly or using a SPOE adapter with no intervening hubs, routers, switches, or other network equipment. Alcatel SPOE adapters separate the serial and FE portions of the cable and route them to their individual ports on the connected device. There are two adapter models: CA-SPOE-ADAPT-1 adapts the Ethernet cable for DB-9 serial and RJ-45 FE devices. [. . . ]