User manual ALCATEL-LUCENT SPEEDTOUCH 605 1

[. . . ] SpeedTouchTM605 Business DSL Routers CLI Reference Guide Release R5. 3. 1 SpeedTouchTM 605 CLI Reference Guide R5. 3. 1 Copyright Copyright ©1999-2005 THOMSON. Passing on, and copying of this document, use and communication of its contents is not permitted without written authorization from THOMSON. The content of this document is furnished for informational use only, may be subject to change without notice, and should not be construed as a commitment by THOMSON. THOMSON assumes no responsibility or liability for any errors or inaccuracies that may appear in this document. [. . . ] 100BaseTFD: 100Mb/s communication speed in full duplex mode. or enter a number between 0 (auto) and 5 (100BaseTFD). REQUIRED OPTIONAL Note state This value should never be changed, except in case of communication problems. OPTIONAL Enable or disable the interface. The default is enabled. EXAMPLE: =>eth device iflist Interface Type Result State ethif1 auto 100BaseTFD UP [forwarding] ethif2 auto 100BaseTFD UP [forwarding] ethif3 auto 100BaseTFD UP [forwarding] ethif4 auto 100BaseTFD UP [forwarding] usbif1 UP [forwarding] =>eth device ifconfig intf=ethif4 state=disabled =>eth device iflist Interface Type Result State ethif1 auto 100BaseTFD UP [forwarding] ethif2 auto 100BaseTFD UP [forwarding] ethif3 auto 100BaseTFD UP [forwarding] ethif4 auto 100BaseTFD DOWN [disabled] usbif1 UP [forwarding] => RELATED COMMANDS: eth device iflist Show status of Ethernet interfaces. E-DOC-CTC-20050531-0059 v1. 0 287 Eth Commands eth device iflist Show status of Ethernet interfaces. SYNTAX: eth device iflist EXAMPLE: =>eth device iflist Interface Type ethif1 auto ethif2 auto ethif3 auto ethif4 auto usbif1 wlif1 wlif2 wlif3 wlif4 wlif5 => Result 100BaseTFD 100BaseTFD 100BaseTFD 100BaseTFD State UP [forwarding] UP [forwarding] UP [forwarding] UP [forwarding] UP [forwarding] UP [forwarding] UP [forwarding] UP [forwarding] UP [forwarding] UP [forwarding] DESCRIPTION: Type: Indicates the configured Ethernet communication speed and duplex mode. Result : Indicates the effective operating status if Type equals "auto". In other cases, when the Ethernet types do NOT match, Result Type will equal "unknown" and no Ethernet connectivity will exist. RELATED COMMANDS: eth device ifconfig Configure an Ethernet interface. 288 E-DOC-CTC-20050531-0059 v1. 0 Eth Commands eth switch group flush Set all the ports to the default settings. All the ports are placed in group 0. SYNTAX: eth switch group flush EXAMPLE: =>eth Group Group Group =>eth =>eth Group => switch group 0 Ports: 4 1 Ports: 1 2 Ports: 2 3 switch group switch group 0 Ports: 1 2 list flush list 34 E-DOC-CTC-20050531-0059 v1. 0 289 Eth Commands eth switch group list List all the configured switch groups. SYNTAX: eth switch group list EXAMPLE: =>eth Group Group Group => switch group list 0 Ports: 4 1 Ports: 1 2 Ports: 2 3 RELATED COMMANDS: eth switch group move Move a specified port to a specified switch group. 290 E-DOC-CTC-20050531-0059 v1. 0 Eth Commands eth switch group move Move a specified port to a specified switch group. SYNTAX: eth switch group move group = <number{0-3}> port = <number{1-4}> where: group port A number between 0 and 4. Represents the group ID to which the port must be moved. REQUIRED REQUIRED EXAMPLE: =>eth Group =>eth =>eth Group Group => switch group 0 Ports: 1 2 switch group switch group 0 Ports: 2 3 3 Ports: 1 list 34 move group=3 port=1 list 4 RELATED COMMANDS: eth switch group list List all the configured switch groups. E-DOC-CTC-20050531-0059 v1. 0 291 Eth Commands eth switch mirror capture Define the specified port to be the Mirror Capture Port. Only one port can be the Mirror Capture Port at any one time. SYNTAX: eth switch mirror capture where: port The port to be the Mirror Capture Port. REQUIRED port = <number{1-4}> Note If no port number is specified, then the port number of the Mirror Capture Port is shown. EXAMPLE: =>eth switch mirror capture port=2 =>eth switch mirror capture Mirror capture port = 2 => RELATED COMMANDS: eth switch mirror egress eth switch mirror ingress Enable or disable the specified port to be the Mirror Egress Port. Enable or disable the specified port to be the Mirror Ingress Port. 292 E-DOC-CTC-20050531-0059 v1. 0 Eth Commands eth switch mirror egress Enable or disable the specified port to be the Mirror Egress Port. Only one port can be the Mirror Egress Port at any one time. But a port can be the Mirror Egress Port and the Mirror Ingress Port at the same time. SYNTAX: eth switch mirror egress port = <number{1-4}> [state = <{enabled | disabled}>] where: port The port to be the Mirror Egress Port. REQUIRED Note state If no port number is specified, then the port number of the current Mirror Egress Port is shown. OPTIONAL Enable or disable the port as Mirror Egress Port. The default is enabled. EXAMPLE: Here port 1 is enabled as Mirror Egress Port =>eth switch mirror egress port=1 =>eth switch mirror egress Egress mirror port = 1 => Here port 1 is disabled as Mirror Egress Port =>eth switch mirror egress Egress mirror port = 1 =>eth switch mirror egress port=1 state=disabled =>eth switch mirror egress => RELATED COMMANDS: eth switch mirror capture eth switch mirror ingress Define the specified port to be the Mirror Capture Port. Enable or disable the specified port to be the Mirror Ingress Port. E-DOC-CTC-20050531-0059 v1. 0 293 Eth Commands eth switch mirror ingress Enable or disable the specified port to be the Mirror Ingress Port. Only one port can be the Mirror Ingress Port at any one time. But a port can be the Mirror Egress Port and the Mirror Ingress Port at the same time. SYNTAX: eth switch mirror ingress port = <number{1-4}> [state = <{enabled | disabled}>] where: port The port to be the Mirror Ingress Port. REQUIRED Note state If no port number is specified, then the port number of the current Mirror Ingress Port is shown. [. . . ] R: indicates the default remote administrator. RELATED COMMANDS: user delete user list Delete a user. Display the users. E-DOC-CTC-20050531-0059 v1. 0 623 User Commands user config Modify a user. You can only modify a user whose privileges are the same or lower than your own privileges. SYNTAX: user config name = <string> [password = <password>] [role = <string>] [descr = <quoted string>] [defuser = <{disabled | enabled}>] [defremadmin = <{disabled | enabled}>] where: name password The user name. REQUIRED OPTIONAL Note role The maximum length is 32 characters. [. . . ]