User manual ALCATEL-LUCENT SPEEDTOUCH 716

[. . . ] SpeedTouchTM716/716g Broadband Voice IAD User's Guide Release R1. 0 SpeedTouchTM716g only SpeedTouchTM 716/716g User's Guide R1. 0 Copyright Copyright ©1999-2005 THOMSON. Passing on, and copying of this document, use and communication of its contents is not permitted without written authorization from THOMSON. The content of this document is furnished for informational use only, may be subject to change without notice, and should not be construed as a commitment by THOMSON. THOMSON assumes no responsibility or liability for any errors or inaccuracies that may appear in this document. [. . . ] In case of problems you can also configure the computer's Ethernet or USB interface with a static private IP address, for example 192. 168. 1. 2, 192. 168. 1. 3, but make sure NOT to use 192. 168. 1. 254 as this is the default IP address of the SpeedTouchTM. ! Your web browser is capable and allows to run Javascripts. For more information, see your web browser's help. Configuration procedure Proceed as follows: 1 2 3 4 5 6 7 Start the web browser on your computer. Browse to the SpeedTouchTM web pages at http://192. 168. 1. 254. The SpeedTouchTM prompts you to enter user name and password. Type "admin" in both fields and click OK. Your browser connects to the SpeedTouchTM web pages. The Quick Setup wizard will guide you through the configuration of your SpeedTouchTM. Follow the instructions and enter the required information where needed. This information should be provided by your ISP. For more information on the different windows shown during this configuration, see " The Quick Setup page" on page 47. 8 At the end of the configuration your SpeedTouchTM will reboot in order to apply the new configuration. E-DOC-CTC-20041126-0014 v3. 0 37 Chapter 3 Configuration 38 E-DOC-CTC-20041126-0014 v3. 0 Chapter 4 SpeedTouchTM Internet Connectivity 4 SpeedTouchTM Internet Connectivity Introduction This chapter provides information on how to configure your SpeedTouchTM according to your preferences and how to access the Internet. Access methods As soon as the SpeedTouchTM and your computers have been configured as outlined in "3 Configuration" on page 37, you are able to connect to the WAN or Internet. Depending on the configuration of the SpeedTouchTM you may have: Direct access As soon as the initial configuration has been done, continuous and immediate access is available via the DSL line. Dial-in access Access must be explicitly established, e. g. by "dialing" into a Broadband Remote Access Server (BRAS). The applied connection protocol model depends on the service profile you selected to configure the SpeedTouchTM and should correspond with the Service Provider's requirements. Direct access As mentioned, as soon as the initial configuration has been done, immediate and uninterrupted WAN access is provided. In case of direct access, the remote organization might ask for a user name and password on an Internet welcome page. Dial-in access The SpeedTouchTM supports both most popular connection methods: PPP over ATM (PPPoA) and PPP over Ethernet (PPPoE). The connection method depends on the service profile you selected to configure the SpeedTouchTM and should correspond with the service Provider's requirements. Routed PPPoA: the SpeedTouchTM needs to be configured for the Routed PPPoA Service. Routed PPPoE: the SpeedTouchTM needs to be configured for the Routed PPPoE Service. Both Services are available via the SpeedTouchTM Quick Setup. Using the SpeedTouchTM PPP dial-in client SpeedTouchTM's embedded PPP dial-in client allows you to establish an Internet connection for all (or a selection of) computers residing on your local network, using only one computer of the network to control the client. If this computer runs: MS Windows XP you can use MS Windows XP's Internet Gateway Device Control Client. See "4. 1 Using the MS Windows XP Internet Gateway Device Control Agent" on page 40 to proceed. Another Operating System you can use the SpeedTouchTM web pages. [. . . ] For more information, see"2. 3. 1 First-time Wireless Client Association" on page 21. 102 E-DOC-CTC-20041126-0014 v3. 0 Chapter 8 Support 8. 4 Troubleshooting Diagnostics tests The Diagnostics Tests page allows you to troubleshoot your SpeedTouchTM connections in a swift and easy way. For more information, see "8. 4. 1 Diagnostics Tests" on page 104 . Common problems If you are having problems with: LAN connectivity, go to "8. 4. 2 Problems with LAN" on page 105. Firmware upgrade, go to "8. 4. 3 Upgrading Problems" on page 106. E-DOC-CTC-20041126-0014 v3. 0 103 Chapter 8 Support 8. 4. 1 Diagnostics Tests The Diagnostics page The Diagnostics page allows you to check the SpeedTouchTM connections: The testing items are listed in chronological order. If a test fails, all remaining tests will fail as well. Starting the Diagnostics Tests Proceed as follows: 1 Open the SpeedTouchTM web pages. [. . . ]