User manual ALESIS ACOUSTIFX

[. . . ] User Manual Table Of Contents Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 About the AcoustiFX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 AcoustiFX Basics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 How to Use This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Important Safety Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Important Safety Instructions (English) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Turn the EFFECT knob to the effect module or parameter you wish to modify. Turn the VALUE knob to select an effect type or value for the module. As soon as you change the value, the EDITED decimal point on the display lights up to show you a change has been made to the current program. If the module has a parameter (PARAM), turn the EFFECT knob to select the parameter. Using the VALUE knob, select a value for the parameter. Continue in this way until you have completed assignments for all modules and parameters. To toggle an effect module on and off, press both pedals while the effect module is selected. 3. 2 4 1 3 5 4. 1 5. 6. To Restore Factory Presets Once you have saved changes to a preset program, you can still recall the original settings. To enter RESTORE FACTORY PRESETS mode, simply hold down the VALUE knob as you turn the unit on and then select the program to for all programs). Press the VALUE be restored (or knob to confirm your selection. Any program changes you have made will be lost, so you might want to copy the program to another location first. See chapter 8 for instructions on how to copy programs. Just turn the EFFECT knob to exit the RESTORE FACTORY PRESETS mode, or turn the unit off and then on again. 21 7 Using the Tuner To Tune Your Guitar 1. In PLAY mode, enter BYPASS by pressing both foot mode pedals at the same time once, or enter MUTE mode by holding them both down for more than half a second. The display will now show tuning information. Make sure your guitar is connected to the AcoustiFX, and play the open string you wish to tune. The left digit of the display indicates the pitch nearest that of the open string. If the # decimal point is lit, the note is a sharp. If it is not lit, the note is a natural. Look at the right digit of the display to determine if the pitch is correct. If the top four segments of the digit are rotating clockwise, then your guitar's pitch is higher than the pitch shown in the first digit. If the bottom four segments are rotating counterclockwise, the pitch is low. The more the pitch is off, the faster the rotation. If no pitch is detected, you'll see a dash in the left digit. [. . . ] This warranty is enforceable only by the original retail purchaser and cannot be transferred or assigned. For the most effective service, the purchaser should register the purchase on the ALESIS website at http://www. alesis. com/support/warranty. htm. During the warranty period, ALESIS shall, at its sole and absolute option, either repair or replace free of charge any product that proves to be defective on inspection by ALESIS or its authorized service representative. In all cases disputes concerning this warranty shall be resolved as prescribed by law. [. . . ]