User manual ALINCO DJ-S17 TFH

[. . . ] VHF/UHF FM TRANSCEIVER DJ-S17 E/TFH DJ-S47 E Instruction Manual VOL VOL NAME SQL KL V/M/C SQL KL /C V/MNA ME MW RPT PO MW RPT PO UHF FM TRANSCEIVER UHF FM TRANSCEIVER DJ-S17 DJ-S47 Thank you for purchasing your new Alinco transceiver. This instruction manual contains important safety and operating instructions. Please read this manual carefully before using the product and keep it for future reference. ALINCO, INC. 2 NOTICE / Compliance Information Statement NOTICE / Compliance Information Statement Conformity Information Alinco, Inc. Electronics Division hereby declare on our sole responsibility that the product(s) listed below comply the essential requirements of the Directive 1999/5/EC, The council of 3/9/99 on Radio Equipment and Telecommunication Terminal Equipment and the mutual recognition of their conformity and with the provisions of Annex, after having performed the required measurements at Notified Bodies per Standards, and relative certificate(s) or document(s) can be reviewed at http://www. [. . . ] " " is displayed on the LCD, and the channel programmed in MC is recalled. Press the key again in the Call mode to return to original operating mode (VFO/memory). NOTE: Refer to "How to Program Call Channel" on page 28 for programming Call channel. 4 IMPORTANT NOTE: · The dial operation of frequency/memory channel is blocked in the Call mode. · It is possible to temporary change the offset and CTCSS/DCS related parameters in the Call mode by entering to the Set mode in the Call channel. · The Scan function is deactivated in the Call mode. · The CALL channel reprogramming is possible but it can't be deleted from the memory channel mode. 4. 7 Receiving 1. Press the key and rotate the dial to adjust the audio level as necessary. key and rotate the dial to adjust the squelch level. 4. Select the frequency that you wish to operate by using the dial. When a signal is received on the frequency that you selected, and S-meter are displayed on the LCD, then the received signal can be heard. The green RX indicator also lights at this time. 4. 7. 1 Monitor Function In case the receiving signal is weak and the audio is intermittently cut off by the squelch, press the MONI key. As long as this key is pressed, the squelch including TSQ/DCS unmutes making the audio easier to hear. · The squelch is unmuted while the MONI key is pressed, regardless of the squelch level setting. · This function unmutes the squelch even if the DCS and Tone Squelch functions are set. 30 4. Basic Operation 4. 8 Transmitting 1. Select the frequency that you wish by using the dial. The red TX indicator turns on while transmitting. While holding down the PTT key, speak into the unit at normal voice from the distance of 5cm (2"). IMPORTANT NOTE: · To transmit a tone-burst signal, press the MONI key while holding down the PTT key. · Speaking too loud, too close or too far from the unit may distort the audio. · This unit is equipped with a special kind of cloth over the built-in microphone for water proof. For this reason, a slight change of tone may happen when you use accessories like external microphones, but this is not abnormal. · "OFF" appears on the display and a beep sounds when the PTT key is pressed with the TX frquency set out of the TX range. [. . . ] Remove the battery pack from the basket. NOTE: The flashing red indicator means that the charger isn't working properly. Stop using it immediately, remove the cord form the outlet and consult with your local Alinco dealer. Specifications *The charging time may vary depending on the condition of the battery pack and the temperature of the environment. Connecting Additional Baskets (EDC-143R/144R) In order to use EDC-143R and EDC-144R, an optional power supply (IEC/EN 609501 compliant) of 1A/5A minimum respectively is required. A DC cable isn't included in the package; the suggested DC cable is 20 AWG wire, shorter than 1m (3feet) in length. [. . . ]