Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual ALLEN & HEATH GL3000. We hope that this ALLEN & HEATH GL3000 user guide will be useful to you.
Lastmanuals help download the user guide ALLEN & HEATH GL3000.
Manual abstract: user guide ALLEN & HEATH GL3000
Detailed instructions for use are in the User's Guide.
[. . . ] SYS-LINK ribbon harness with D type connector fixings already fitted. SYS-LINK Fitting Instructions (AP2664) SYS-LINK Application notes (AP2665)
·
TOOLS REQUIRED :
SOLDERING IRON with small tip SOLDER LONG NOSE 1pt CROSS POINT
2
GL3000 & GL3300 SYS-LINK OPTION
ALLEN & HEATH
Z
PRELIMINARY:
To fit the SYS-LINK option it is necessary to partially remove GROUP 1 circuit board assembly to enable access to the SYS-LINK solder pads. [. . . ] 4, prepare the solder pads on the circuit boards with new solder to ease the soldering of the SYS-LINK wires. Note, the wires are soldered to the trackside of the circuit boards and not the component side. It is recommended that the wires in the SYS-LINK harness are soldered to each circuit board in the following order: GROUP 4 then GROUP 3 then GROUP 2 then GROUP 1 then LEFT and then finally the RIGHT PCB.
4
GL3000 & GL3300 SYS-LINK OPTION
ALLEN & HEATH
11
MOUNTING THE SYS-LINK CIRCUIT BOARD:
The SYS-LINK circuit board mounts onto the GROUP 1 circuit board using the 3 pillars already fitted to the SYS-LINK circuit board assembly. On the GL3000 GROUP circuit board, one mounting hole requires drilling. 5 for details of drilling the extra mounting hole.
fig. 5
To fit the SYS-LINK circuit board to the GROUP circuit board, unscrew the 3 screws already partly screwed into the mounting pillars and align with the holes in the GROUP circuit board. 6, slide the SYS-LINK harness toward the back of the console and down the gap between the CONNECTOR circuit board and the GROUP circuit boards. 2, fit the GROUP and SYS-LINK circuit board assembly and re-connect the flexible flat cables (D) to the GROUP and LEFT circuit boards.
12
FITTING THE SYS-LINK HARNESSES :
Refering to fig. 6 below, fit the 4 SYS-LINK ribbon harnesses to the connectors on the edge of the SYS-LINK circuit board. Note which connector each harness plugs onto and the correct alignment of pin 1 with the red stripe on the ribbon cable. Remove the D type mounting screws from the D type connectors and mount them onto the rear panel using the fixings supplied. Check the connectors are mounted into the correct apertures on the rear panel.
SYS-LINK HARNESS
SYS-LINK RIBBON HARNESSES
fig. [. . . ] The SYS-LINK circuit diagram and technical details are included for reference. The SYS-LINK Applications Note AP2665 is included separately with these fitting instructions. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE ALLEN & HEATH GL3000
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual ALLEN & HEATH GL3000 will begin.
