User manual ALPINE CDA-W560EG

[. . . ] R EN CDA-W560E CDA-W560EG CD/CST/DSP RECEIVER · OWNER'S MANUAL Please read before using this equipment. CH ES · ES IT ALPINE ELECTRONICS MARKETING, INC. 1-1-8 Nishi Gotanda, Shinagawa-ku, Tokyo 141-0031, Japan Phone 03-5496-8231 ALPINE ELECTRONICS OF AMERICA, INC. 19145 Gramercy Place, Torrance, California 90501, U. S. A. Phone 1-800-ALPINE-1 (1-800-257-4631) ALPINE ELECTRONICS OF CANADA, INC. [. . . ] The display will show PS-1 with the first press and will increase by one with each successive press up to PS-9. The tape indicator will blink showing the direction of your search. · The FUNCTION mode will be cancelled when an operation has not been performed in 10 seconds. Blank Skip (B. SKIP) Blank sections on the tape lasting 15 seconds or more are skipped. 2 1 Press FUNCTION/SETUP to select the FUNCTION mode. FUNCTION mode Press once during tape play to advance to the beginning of the next selection. If you wish to advance to the beginning of a selection further ahead, press repeatedly until the number of selections you would like to skip is shown in the display. The display will show PS+1 with the first press and will increase by one with each successive press up to PS+9. The tape indicator will blink showing the direction of your search during searching operation. SETUP mode NORMAL mode 2 3 4 Press / or - to select B. SKIP mode, then press -/J / ENT. . The mode that is blinking at the centre of the display is the selected mode. · The programme sensor feature is functional in the tape play mode only. · You can advance to the 9th (max. ) programme or return to the 8th (max. ) programme. Press / or - to select ON, then press -/J / ENT. . ON OFF To cancel, select B. SKIP OFF with the above procedure. · The FUNCTION mode will be cancelled when an operation has not been performed in 10 seconds. Scanning Programmes The first 10 seconds of each programme on the tape will be played back in succession. 1 Press FUNCTION/SETUP to select the FUNCTION mode. FUNCTION mode SETUP mode NORMAL mode 2 3 Press / or - to select SCAN mode, then press -/J / ENT. . The mode that is blinking at the centre of the display is the selected mode. Press / or - to select ON, then press -/J / ENT. . ON OFF · The SCAN operation cannot detect blank sections of less than 4 seconds. · When you have found a desired track for listening, switch the function OFF with the above procedure. · The FUNCTION mode will be cancelled when an operation has not been performed in 10 seconds. 15-EN Radio Operation (SEARCH) //- Manual Storing of Station Presets 1 2 See "Listening to Radio" and set the frequency to that of the desired broadcast station. Press FOLDER/PRESET and within 10 seconds press / or -, select P-MEMO mode, and press -/J / ENT. . BAND SOURCE/POWER g f P-MEMO A-MEMO 3 Within 10 seconds press / or -, select the number (1 to 6) that you would like to store, and press -/J / ENT. . The blinking display will change to steady and the broadcast station will be stored. -/J / ENT. FOLDER/PRESET Listening to Radio FM1-- 3 FM1-- 3 1 Press SOURCE/POWER to select the TUNER mode. The aerial will extend when the TUNER mode is set. (Only on cars equipped with a power aerial. ) TUNER TAPE CD CHANGER* · A total of 18 stations can be stored in the preset memory (6 stations for each band; FM1, FM2 and AM). · If you store a station in a preset memory which already has a station, the current station will be cleared and replaced with the new station. (* Only when the changer is connected) Automatic Memory of Station Presets 2 3 Press BAND to select the band. FM1 FM2 AM 1 2 Press BAND to display the band you wish to receive. FM1 FM2 AM Press g , f or , to search for a desired broadcast station (frequency). g f: Manual mode Press and hold to change the frequency continuously. : : (Press and hold) Local mode (SEEK) Distance mode (DX SEEK) Press FOLDER/PRESET and within 10 seconds press / or -, select A-MEMO mode, and press -/J / ENT. . P-MEMO A-MEMO · Manual mode: The frequency is manually tuned in steps (Manual tuning). · Local mode: Only strong stations will be automatically tuned in (Automatic Seek Tuning). · Distance mode: Both strong and weak stations will be automatically tuned in (Automatic Seek Tuning). The tuner will automatically seek and store 6 strong stations in the selected band. They will be stored into buttons 1 to 6 in order of signal strength. When the automatic memory has been completed, the tuner goes to the station stored in preset location no. · If no stations are stored, the tuner will return to the original station you were listening to before the auto memory procedure began. 16-EN Tuning to Preset Stations 1 2 Press BAND to select the band. FM1 FM2 AM CD Changer Operation (Optional) //Rotary encoder f BAND SOURCE/POWER Press / or - to select the preset number. The selected broadcast station will be received. FM1- 1 87. 50 MHz Preset number display (Display of the received broadcast station stored in preset numbers "1" to "6". ) · The ST indicator appears on the display when a stereo FM station is tuned in. g -/J / ENT. Station Title Search Function If titles for radio stations are entered, you can search for a radio station from its title. Controlling CD Changer 1 2 3 Press (SEARCH) in TUNER mode to switch to Title Search mode. The first title input blinks in the display. 1 Press SOURCE/POWER to set the changer mode. TUNER TAPE CD CHANGER* Press / or - to select the desired title within 10 seconds. [. . . ] If so, please contact your authorized ALPINE dealer for assistance. · Be sure to connect the speaker (­) leads to the speaker (­) terminal. Never connect left and right channel speaker cables to each other or to the vehicle body. DO NOT DAMAGE PIPE OR WIRING WHEN DRILLING HOLES. When drilling holes in the chassis for installation, take precautions so as not to contact, damage or obstruct pipes, fuel lines, tanks or electrical wiring. Failure to take such precautions may result in fire. DO NOT USE BOLTS OR NUTS IN THE BRAKE OR STEERING SYSTEMS TO MAKE GROUND CONNECTIONS. Bolts or nuts used for the brake or steering systems (or any other safety-related system), or tanks should NEVER be used for installations or ground connections. [. . . ]