User manual ALPINE CDE-9845RX CORRECTION

[. . . ] · ISTRUZIONI PER L'USO Si prega di leggere prima di utilizzare il attrezzatura. · ANVÄNDARHANDLEDNING Innan du använder utrustningen bör du läsa igenom denna användarhandledning. ES IT ALPINE ELECTRONICS MARKETING, INC. 1-1-8 Nishi Gotanda, Shinagawa-ku, Tokyo 141-0031, Japan Phone 03-5496-8231 ALPINE ELECTRONICS OF AMERICA, INC. 19145 Gramercy Place, Torrance, California 90501, U. S. A. [. . . ] to select the Treble Control mode. BASS LV TRE LV normal mode BASS LV CDE-9846R/CDE-9846RM: Press MODE to select the Treble Control mode. BASS LV TRE LV SUBW BALANCE FADER DEFT VOLUME BASS LV 1 CDE-9845RX: Press CENT. to select the Bass Control mode. BASS LV TRE LV normal mode BASS LV 2-1 CDE-9846R/CDE-9846RM: Press MODE to select the Bass Control mode. BASS LV TRE LV SUBW BALANCE FADER DEFT VOLUME BASS LV Setting the treble Centre frequency: Press g or f to select the desired treble centre frequency. 7. 5kHz 10. 0kHz 12. 5kHz 15. 0kHz 7. 5kHz The displayed Treble frequency is emphasized. 2-1 Setting the bass centre frequency: Press g or f to select the desired bass centre frequency. 60Hz 80Hz 100Hz 120Hz 60Hz 2-2*2 Setting the treble level: Turn the Rotary encoder (CDE-9845RX) or press 4 and 3 (CDE-9846R/CDE-9846RM) to select the desired treble level (-7~+7). You can emphasize the treble level. The displayed bass frequency is emphasized. 2-2 Setting the bass band width (Q-Factor): Press BAND to select the desired bass band width. 1 2 3 4 (Narrow) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Wide) Change the boosted bass band width to wide or narrow. A wide setting will boost a wide range of frequencies above and below the centre frequency. A narrower setting will boost only frequencies near the centre frequency. · If no operation is performed within 15 seconds, the treble control setting will be turned off automatically. · The treble level settings will be individually memorized for each source (FM, MW (LW), CD, etc. ) until the setting is changed. The Treble frequency settings adjusted for one source are effective for all other sources (FM, MW (LW), CD, etc. ). · This function is inoperable when DEFT is set to ON. *2 CDE-9845RX: The adjustment can also be made by pressing the Rotary encoder (MODE). Refer to "Adjusting Bass/Treble/Balance (Between Left and Right)/Fader (Between Front and Rear)/Defeat" (page 13). 2-3*2 Setting the bass level: Turn the Rotary encoder (CDE-9845RX) or press 4 and 3 (CDE-9846R/CDE-9846RM) to select the desired bass level (-7~+10). You can emphasize or weaken the bass level. Turning Loudness On/Off Loudness introduces a special low- and high-frequency emphasis at low listening levels. From the SETUP menu, choose from Sound Customizing, Visual Customizing, etc. , to make your desired settings. 1 2 3 4 Press TITLE and select the Title Display. For details, see "Displaying the Title/Text" (page 15). CDE-9845RX Press and hold TITLE for at least 2 seconds. Turn the Rotary encoder (CDE-9845RX) or press 4 and 3 (CDE-9846R/CDE-9846RM) to select the desired letter/numeral/symbol available for naming. Press Rotary encoder (CDE-9845RX) or MODE (CDE-9846R/CDE-9846RM) to store the first character. The first character will stop blinking and the display will automatically advance to the next character. When that character begins to blink, you may choose the next letter or symbol of your title. g f FUNC. /SETUP Rotary encoder BAND CDE-9846R/CDE-9846RM MODE 4 BAND 5 Repeat steps 3 and 4 above to complete the titling. Pressing the Rotary encoder (CDE-9845RX) or MODE (CDE-9846R/CDE-9846RM) after entering the 8th character automatically stores the title into memory. When entering a title of less than 8 characters (for example, 3 character title): After entering 3 characters, the 4th character space will be blinking. Go to step 6 to complete the title. 6 Press TITLE to record the title. · If you cancel while entering a title, selected characters are not written. · You can enter 18 CD titles on this unit. If you try to store beyond the limit, the display will show "FULL DATA. " At this point, no more titles can be stored. To input a new title, one of the previously inputted titles must first be deleted. · When you want to erase a title, enter the " " symbol into all spaces. · The operations described in steps 3 to 5 must be made within 10 seconds. [. . . ] Marié Q12. Edad Q13. Estado civil 1. Selbständige/Firmeninhaber/freiberuflich Tätige 2. Entrepreneur/Travailleur indépendant/ Free-lance 2. Propietario de empresa/Autónomo/ Profesional independiente 2. [. . . ]