User manual ALPINE CTM-1503R

[. . . ] R CTM-1503R Digital Commander/Receiver · OWNER'S MANUAL Please read before using this equipment. · BEDIENUNGSANLEITUNG Lesen Sie diese Bedienungsanleitung bitte vor Gebrauch des Gerätes. · MODE D'EMPLOI Veuillez lire avant d'utiliser cet appareil. · MANUAL DE OPERACIÓN Léalo antes de utilizar este equipo. [. . . ] Press the BAND button repeatedly until the desired band is displayed. Press the station Preset button that has your desired radio station in memory. The display shows the band, preset number with a triangle and frequency of the station selected. DE IT SE 7-EN RDS Operation INTLZ BAND AF PTY T. INFO DN g f UP F 2 Setting RDS Reception Mode and Receiving RDS Stations The RDS (Radio Data System) is a radio information system using the 57 kHz subcarrier of regular FM broadcast. The RDS allows you to receive a variety of information such as traffic information, station names, and to automatically re-tune to a stronger transmitter that is broadcasting the same programme. Tips The RDS digital data includes the followings: PI Programme Identification PS Programme Service Name AF List of Alternative Frequencies TP Traffic Programme TA Traffic Announcement PTY Programme Type EON Enhanced Other Networks Recalling Preset RDS Stations 1 2 3 4 Press the F button so that the F indicator lights up. Press the AF button to activate the RDS mode. The display shows "AF" when the RDS mode is activated. Press the F button to activate the normal mode. Make sure that the F indicator light goes out, then press the preset location button in which your desired RDS station is preset. If the preset station's signal is weak, the unit automatically searches and tunes to a stronger station in the AF (Alternative Frequencies) list. If the preset station and the stations in the AF list cannot be received: The unit searches again for a station in the PI (Programme Identification) list. If there are still no stations receivable in the area, the unit displays the frequency of the preset station and the preset indicator disappears. NOTE For presetting the RDS stations, refer to the Radio Operation section. The RDS stations can be preset in the FM1 and FM2 bands only. 1 2 3 Press the F button so that the F indicator lights up. Press the AF button to activate the RDS mode. Press the DN g or f UP button to tune in the desired RDS station. NOTE When the BAND button is pressed and held for more than 2 seconds while a station name is displayed, the display shows the station frequency for 5 seconds. 4 5 Press the AF button again to deactivate the RDS mode. Press the F button to activate the normal mode. The F indicator light goes out. 5 8-EN Receiving RDS Regional (Local) Stations PTY (Programme Type) Tuning 1 2 3 1 2 Press and hold the INTLZ button for at least 3 seconds to activate the setting mode. Press the Preset 2 button to turn on or off the REG (Regional) mode. In the REG OFF mode, the unit automatically keeps receiving the related local RDS station. Press the INTLZ button to deactivate the setting mode. 1 2 Press the F button so that the F indicator lights up. Press the PTY button to activate the PTY mode. The Programme Type of the station being currently received will be displayed for 5 seconds. · If there is no receivable PTY broadcast, "NO PTY" will be displayed for 2 seconds. NOTE If no button is pressed within 5 seconds after pressing the PTY button, the PTY mode will be automatically cancelled. Receiving Traffic Information Press the T. INFO button repeatedly until the T. INFO indicator appears in the display. [. . . ] ( / : Green Green/Black Rear Left White White/Black Grey/Black Grey Front Left Front Right Violet/Black Violet Rear Right Speakers Front Left Amplifier Front Right CD changer (Sold separately) " ; # ; Amplifier Rear or Subwoofers When Subwoofer is set to OFF: Output is from Rear speakers. When Subwoofer is set to ON: Output is from Subwoofer. For details on how to set the Subwoofer to ON/OFF, see "Subwoofer On and Off" on page 4. 18-EN 1 Antenna Receptacle Connect to the supplied ISO antenna convertor plug. 2 Audio Interrupt In Lead (Pink/Black) Connect this lead to the Audio Interface output of a cellular phone which provides ground shorting when a call is received. If a device having the interrupt feature is connected, audio will be automatically muted whenever the interrupt signal is received from the device. [. . . ]