User manual ALPINE CVA-1004R

[. . . ] R EN CVA-1004R MOBILE MEDIA STATION · OWNER'S MANUAL Please read before using this equipment. · BEDIENUNGSANLEITUNG Lesen Sie diese Bedienungsanleitung bitte vor Gebrauch des Gerätes. · MODE D'EMPLOI Veuillez lire avant d'utiliser cet appareil. · MANUAL DE OPERACIÓN Léalo antes de utilizar este equipo. [. . . ] When the monitor is closed: displayed in the subdisplay · In case a 6-disc DVD changer is connected: In DVD changer mode, press FUNC to illuminate the "FUNC" indicator and go to step 1. 27-EN Navigation System Operation (Optional) 3 SOURCE/PWR MUTE/SETUP Press g or f to select ON or OFF. ON: The volume level of the navigation system's voice guidance can be adjusted in 15 steps. OFF:The navigation system's voice guidance is not output. (For details about adjusting volume level, refer to "Adjusting Volume/Balance/Fader" on page 8. ) For any other settings, press preset 5 or another preset button. 4 Preset 5 After setting is completed, press MUTE/SETUP to return to normal mode. NOTES · The volume level of the audio will be automatically reduced when the voice guidance of the Navigation system starts. · When the voice guidance of the Navigation system starts to interrupt the audio, the display is automatically changed to the navigation screen. g f Turning on the Navigation Mode If an optional Alpine Navigation System is connected, the display shows the navigation screen. Interrupt Feature (NAV. MIX OUT) With an Alpine navigation system connected to the CVA-1004R, the navigation system's voice guidance is mixed in and output from the Rear/ Subwoofer Output RCA connectors. This function is not available when an external audio processor is connected. 1 Press SOURCE/PWR to select the Navigation mode. NOTE If the Navigation mode does not appear in the display by pressing SOURCE/PWR, set the external setting of NAV. IN to ON (Refer to "Setting the External Input" on page 42). 1 2 3 When the monitor is open, press and hold MUTE/SETUP for at least 2 seconds. Press preset 5 to activate the SYSTEM setting mode. Press preset 5 again to select NAV. MIX OUT. Select ON to allow the navigation system's voice guidance to interrupt the external amplifier. For any other settings, press preset 5 or another preset button. Interrupt Feature (NAV. MIX) With an Alpine navigation system connected to the CVA-1004R, the voice guidance of the navigation system will be mixed with the radio or CD audio, etc. You can also adjust the volume level of the voice guidance. If you use this unit connected to an external audio processor, you cannot use this function (except PXA-H700 series). 1 2 When the monitor is open, press and hold MUTE/SETUP for at least 2 seconds. Press preset 5 to activate the SYSTEM setting mode. MIX. 4 After setting is completed, press MUTE/SETUP to return to normal mode. 28-EN MobileHubTM Link Operation (Optional) NOTES · When a portable telephone is not connected, "NO PHONE" is displayed for at least 2 seconds, then the mode returns to the original source mode. · When the portable telephone is taken off the Junction BOX during an incoming or outgoing call, or during a hands-free call, the call will be treated as an ordinary one by the portable telephone. · When there is an incoming call while the power of CVA-1004R is OFF, the power of CVA-1004R will turn ON automatically for an ordinary call by the portable telephone, but not for a hands-free call. · Even if the power of the portable telephone is OFF, when CVA-1004R is set to the telephone mode, the power of the portable telephone will be turned ON. · Even if the ACC power of the vehicle is turned OFF (even if the engine is stopped) during a hands-free call, the call is not disconnected, and an ordinary call by the portable telephone is possible. · If there is an incoming call during operation (except an outgoing call or talking), operation mode will end and switch to the incoming or talking mode. · An outgoing call from a portable telephone is also possible. However, you cannot perform different operations at the same time from a portable telephone and CVA-1004R as malfunction can result. [. . . ] $ RGB Input Connector Connect to the RGB output terminal of the KCE-104V. % Rear/Subwoofer Output RCA Connectors RED is right and WHITE is left. & AUX Audio Input (AUX1) Connectors ( AUX Video Input (AUX1) Connector ) RCA Extension Cable (Included with DVD video player) ~ RCA Extension Cable (Sold Separately) + RCA Extension Cable (Included with the KCE-104V) , To Front/Rear PREOUT Terminals of the KCE-104V - To Subwoofer Terminals of the KCE-104V . Connect to the AUX Input (AUX1) Connectors of the CVA-1004R / To AUX1 Output Terminals of the KCE-104V : To AUX2 Output Terminals of the KCE-104V ; To Sound Input Terminals of the KCE-104V (from the CVA-1004R) < To AUX Input1 Terminals of the KCE-104V = To AUX Input2 Terminals of the KCE-104V > To AUX Input3 Terminals of the KCE-104V ? [. . . ]