Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual ALPINE KCE-104V. We hope that this ALPINE KCE-104V user guide will be useful to you.
Lastmanuals help download the user guide ALPINE KCE-104V.
Detailed instructions for use are in the User's Guide.
[. . . ] Failure to take such precautions may result in fire. dO NOT USE BOLTS OR NUTS IN THE BRAKE OR STEERING SYSTEMS TO MAKE GROUND CONNECTIONS. Bolts or nuts used for the brake or steering systems (or any other safety-related system), or tanks should NEVER be used for installations or ground connections. Using such parts could disable control of the vehicle and cause fire etc. [. . . ] To ensure safety, always contact the dealer where you purchased this product to have the work done. aRRANGE THE WIRING SO IT IS NOT CRIMPED OR PINCHED BY A SHARP METAL EDGE. Route the cables and wiring away from moving parts (like the seat rails) or sharp or pointed edges. This will prevent crimping and damage to the wiring. If wiring passes through a hole in metal, use a rubber grommet to prevent the wire’s insulation from being cut by the metal edge of the hole. Operation
For proper operation, connect the REAR SEL1 or REAR SEL2 lead to chassis ground through a switch, etc. for details , consult an authorized ALPINE dealer. When the CVA-1004/CVA-1004R is connected, the V. ANA is not accessible in the SETUP menu. Also, operations can be performed from the CVA-1004/CVA-1004R when connected. For details, refer to the Owner's Manual of the CVA-1004/ CVA-1004R. Switching the output source
The visual output from AUX OUT1/2 for each monitor can be switched. Connect the REAR SEL1 or 2 lead momentarily to chassis ground. Each connection changes the visual source for each monitor. AUX1 → AUX2 → AUX3(CAMERA) → OFF∗ → AUX1
∗Sólo al conectarlo al CVA-1004/CVA-1004R
AUX1 → AUX2 → AUX3(CAMERA) → OFF∗ → AUX1
• If you select an unconnected source, noise may occur. SETUP
Each setting can be performed by the procedure shown below. The setup menu is common for both REAR SEL1 and REAR SEL2. Connect the REAR SEL1 or 2 lead to chassis ground for at least 2 seconds. Connect the REAR SEL1 or 2 lead momentarily to the ground to select SETUP item. Connect the REAR SEL1 or 2 lead to chassis ground for at least 2 seconds to change each setting. MODE3: Visual Effect is applied continuously on the two monitors which are output from AUX OUT 1/2 terminals. MODE4: MODE 1 to 3 are applied in random sequence among the monitors. [. . . ] Connect this lead to the positive side of the vehicle’s reverse lamp. The video input will automatically switch to the AUX3(CAMERA) whenever the vehicle is backing up. 5 Battery Lead (Yellow)/Fil de batterie (jaune)/Cable de la batería (amarillo) Connect this lead to the positive (+) post of the vehicle's battery. 2 Set the Colour Contorl for the TV Tuner to "OFF". [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE ALPINE KCE-104V
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual ALPINE KCE-104V will begin.
