User manual ALPINE MC-10

[. . . ] Colombo 8, 20090 Trezzano Sul Naviglio (MI), Italy Phone 02-484781 ALPINE ELECTRONICS Of u. K. , LTd. ALPINE ELECTRONICS Of AMERICA, INC. 19145 Gramercy Place Torrance, California 90501 U. S. A. Phone 1-800-ALPINE-1 (1-800-257-4631) ALPINE ELECTRONICS fRANCE S. A. R. L. ALPINE ELECTRONICS Of CANAdA, INC. 777 Supertest Road Toronto Ontario M3J 2M9, Canada Phone 1-800-ALPINE-1 (1-800-257-4631) 161-165 Princess Highway, Hallam Victoria 3803, Australia Phone 03-8787-1200 ALPINE ITALIA S. p. A. ALPINE ELECTRONICS Of AuSTRALIA PTy, LTd. ALPINE ELECTRONICS dE ESPAÑA, S. A. Portal de Gamarra 36, Pabellón, 32 01013 Vitoria (Alava)-APDO 133, Spain Phone 945-283588 Leuvensesteenweg 510-B6, 1930 Zaventem, Belgium Phone 02-725 1315 Wilhelm-Wagenfeld-Str. 1-3 80807 München, Germany Phone 089-32 42 640 ALPINE ELECTRONICS GmbH ALPINE ELECTRONICS (BENELuX) GmbH Printed in China Operating Instructions WARNING This symbol means important instructions. Failure to heed them can result in serious injury or death. [. . . ] If swallowed, consult a physician immediately. USE THE CORRECT AMPERE RATING WHEN REPLACING FUSES. Failure to do so may result in fire or electric shock. USE THIS PRODUCT FOR MOBILE 12V APPLICATIONS. Use for other than its designed application may result in fire, electric shock or other injury. WARNING This symbol means important instructions. Failure to heed them can result in injury or material property damage. HALT USE IMMEDIATELY IF A PROBLEM APPEARS. Failure to do so may cause personal injury or damage to the product. Return it to your authorized Alpine dealer or the nearest Alpine Service Center for replacing. CAUTION PRECAUTIONS Product Cleaning Use a soft dry cloth for periodic cleaning of the product. For more severe stains, please dampen the cloth with water only. Anything else has the chance of dissolving the paint or damaging the plastic. Temperature Be sure the temperature inside boat is between +60°C (+140°F) and -10°C (+14°F) before turning your unit on. Maintenance If you have problems, do not attempt to repair the unit yourself. Return it to your Alpine dealer or the nearest Alpine Service Station for servicing. 2 Basic Operation Installation MC10 Display Unit Optional Add-on Commander Optional RUE-M1RF 333MHz Wir eless 2. 4GHz Wir eless MC1 GND +12V BLACK : connect to Ground (GND) YELLOW : connect to 12V(+): ACC (switched) GND +12V 2. 4GHz Wir eless GND +12V MC10 Transceiver Unit To 10P Sub Display Connector IDA-X100M To Steering Wheel Jack OR GND +12V BLACK : RED : connect to Ground (GND) connect to 12V(+): ACC (switched) CDA-9886M 3 Program Menu MC10 Display unit Enter Program Mode Program Menu Options 1. ID NUMBER This is the serial number of the display unit. * Range of serial numbers: 00001 to 99999 Signal strength between a display unit and the closest display or transceiver unit in the MC10 wireless system * Range of strength: [ ] to Wireless signal connection status between a display unit and the transceiver unit * Values: [CONNECTED, NO CONNECT] When set to ON, turns a display unit into a signal repeater for communicating with MC1 add-on commander units that are installed outside the MC10 system communication range * Values: [OFF, ON] Sets brightness or dimness of LCD display characters * Values: [5, 4, 3, 2, 1, 0] Turns LCD backlighting ON or OFF Turns keypad button backlighting ON or OFF Sets temperature scale to degrees F or degrees C Menu selection for pairing or re-pairing any MC1 or MC10 display units with any existing MC10 system. RESET MC1 also restores factory default setting 2. RESET MC1 * Note: Bold indicates default menu selection for this program menu option 4 Program Mode Example 1. Press VOL + or VOL ­ to adjust the current CONTRAST value 2. Press VOL + or VOL ­ until CONTRAST shows on top line of display 5. [. . . ] Power on the MC10 system that you want to add the additional MC10 display unit to 2. Connect power and ground wires of new MC10 display unit 3. Wait at least 20 seconds, then enter the Program Menu (see Program Menu Example) 4. Go to the RESET MC1 option, then press ENT button 5. [. . . ]