User manual ALPINE MRV-F401

[. . . ] 1 of 2 4/3/2 Channel V12 Series Power Amplifier MRV-F401 100 1 0. 5 100 1 0. 5 4/3/2 CHANNEL POWER AMPLIFIER 1 ST 1+2 OFF HP LP 50 (Hz) 200 4 (V) 0. 2 3 ST 3+4 OFF HP LP 50 (Hz) 200 4 (V) 0. 2 1/2 3/4 1+3/2+4 MRV-F401 INPUT MODE FILTER CROSSOVER GAIN INPUT MODE FILTER CROSSOVER GAIN INPUT CHANNEL CHANNEL-1/2 CHANNEL-3/4 Features · 4/3/2 CHANNEL OPERATION - Can be used in a 4 channel mode providing 40W x 4 into 4 ohms or 50W x 4 into 2 ohms, or in mono mode producing 100W x 2 into 4 ohms. (all power ratings are from 20Hz to 20kHz at 12V DC). MULTIMODETM CAPABILITY - The MRV-F401 can operate in 4-channel stereo and bridged mono modes simultaneously. [. . . ] TOP MOUNTED LED POWER INDICATOR NON-FADING PRE-AMP OUTPUT - A set of non-fading preamp outputs are included which can eliminate the need for RCA "Y" connectors and allows for greater system flexibility. DC STRAIGHT DESIGN - Fewer components in the audio path to improve sound quality. SOLID COPPER BUS BARS - Improved power transfer and less voltage drop in power supply. LARGE INTERNAL CAPACITANCE - The MRV-F401 has 16, 400uF of internal capacitance. ISOLATED AUDIO AND POWER SUPPLY SECTIONS · · · · · · · · · · · · Specifications Power Output RMS Power (at 12V, 20-20kHz) Per Channel into 4 . . . . . . . . . . . . . . . . . . . . . . . 40W x 4 (0. 08% THD) Per Channel into 2 . . . . . . . . . . . . . . . . . . . . . . . . . . 50W x4 (0. 3% THD) Bridged 2 Channel into 4 . . . . . . . . . . . 100W x 2 (0. 3% THD) Dynamic Power (at 14. 4V, 20-20kHz) Per Channel into 4 . . . . . . . . . . . . . . . . . . . . . . 60W x 4 (0. 08% THD) Per Channel into 2 . . . . . . . . . . . . . . . . . . . . . . . . . 80W x 4 (0. 3% THD) Bridged 2 Channel into 4 . . . . . . . . . . . 160W x 2 (0. 3% THD) Frequency Response . . . . . . . . . . . . . . . . . . . . . 10Hz to 50kHz (±0, -1 dB) Signal-to-Noise Ratio . 100dBA(referenced to rated power) Input Sensitivity (for rated power) Line inputs . . . . . . . . . . . . . . . . . . . . . . . . . . 200mV-4V (500mV at detent) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] (240x53x330mm) Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13oz. (4. 0kg. ) Specifications and design are subject to change without notice. . MRV-F401 4/3/2 Channel V12 Series Power Amplifier Ground Lead (Black) 2 of 2 - + Fuse Holder Battery Power Wire (Optional) Power Distribution Block (Optional) Battery Lead (Yellow) Battery This Amplifier is Capable of running MultiModeTM 4 Ohm Mono Loading ONLY Front Left Speaker Output Lead (+) 2 Ohm or 4 Ohm Stereo Loading Front Left Speaker Output Lead (+) Front Left Speaker Output Lead (-) Front Right Speaker Output Lead (-) Front Right Speaker Output Lead (-) Front Right Speaker Output Lead (+) 4 Ohm Mono Loading ONLY Rear Left Speaker Output Lead (+) 2 Ohm or 4 Ohm Stereo Loading Rear Left Speaker Output Lead (+) Rear Left Speaker Output Lead (-) Rear Right Speaker Output Lead (-) Rear Right Speaker Output Lead (-) Rear Right Speaker Output Lead (+) Remote - Out Remote-On Lead (+12V Input turns Amp on) White (Left) Front Output Red (Right) White (Left) Rear Output Red (Right) 1 4 2 5 3 6 CH-3 (L) CH-1 CH-1+3 ­ CH-2 + ­ CH-1 + 20A 20A BATTERY REMOTE GND 20A INPUT (R) (R) (L) CH-4 CH-2 CH-2+4 ­ CH-4 ­ + ­ CH-3 BRIDGED + + SPEAKER OUTPUT 20A PRE OUT FUSE POWER SUPPLY Non-Fading Pre-Amp OutPut Connect to Optional Amplifier 2/1 CHANNEL POWER AMPLIFIER 0° 180° 1(MONO) ST 1+2 OFF HP LP NOM 4V OFF ON OFF ON CH-3 (L) CH-1 CH-1+3 ­ ­ MRV-T501 PHASE INPUT MODE FILTER INPUT LEVEL PARAME EQ LOW IMPEDANCE BRIDGED CH-2 + ­ SPEAKER CH-1 + OUTPUT + (R) INPUT (R) CH-4 2 2+4 ­ PRE OUT (L) CH-4 + ­ CH-3 + R. 230197 ® [. . . ]