User manual ALPINE PKG-1000P

[. . . ] R EN PKG-1000P Rear Seat Entertainment Package Système de divertissement pour les sièges arrière Paquete de entretenimiento para asientos traseros Entertainment-Paket für den Rücksitz Sistema di intrattenimento per sedili posteriori Underhållningspaket för baksäte · OWNER'S MANUAL Please read before using this equipment. MODE D'EMPLOI Veuillez lire avant d'utiliser cet appareil. MANUAL DE OPERACIÓN Léalo antes de utilizar este equipo. · BEDIENUNGSANLEITUNG Bitte vor Gebrauch des Gerätes lesen. [. . . ] Contrast can be adjusted from ­15 (LOW) to +15 (HIGH). 4 Press ENT to finish adjustments or wait 10 seconds until OSD disappears; the adjustment will be saved automatically. 6-EN PKG-1000P_EN. indd EN6 5/17/2005 1:39:40 PM Adjusting Sharpness 2 3 1 2 Press or and select SHARPNESS. Screen quality can be adjusted from -15 (SOFT) to +15 (HARD). Press and hold SELECT for at least 2 seconds to show the SETUP menu. Press SELECT to switch to DISP MODE from PICTURE. To change each mode, press or . 4 Press ENT to finish adjustments or wait 10 seconds until OSD disappears; the adjustment will be saved automatically. Each press changes the display modes as follows: Resetting the Picture Adjustment 2 Press or and select RESET. WIDE Normal images are expanded uniformly in the horizontal direction and are displayed over the entire screen. Press ENT to reset the picture adjustments. · If you do not press ENT within 10 seconds, OSD disappears and the reset adjustments will not be saved. 3 Switching Display Modes Display mode on the screen can be adjusted to Wide, Zoom, Cinema and Normal. · Each source can be adjustable individually. · Adjusting should be made within 10 seconds, otherwise OSD (On Screen Display) will be automatically turned off. SELECT ZOOM Normal images are expanded in the horizontal direction and are displayed over the entire screen. The expansion ratio increases towards the right and left edges of the screen. CINEMA Normal images are expanded in the horizontal and vertical directions. The top and bottom of the image are cut off. This mode is suited for 16:9 cinema size images. Front Panel Controls NORMAL Normal image (4:3) SELECT 3 Press the ENT button to finish adjustments or wait 10 seconds until OSD disappears; the adjustment will be saved automatically. Remote Control 7-EN PKG-1000P_EN. indd EN7 5/17/2005 1:39:45 PM VISUAL EQ Operation You can select a mode suitable for the subject image. · Each source can be adjustable individually. · Adjusting should be made within 10 seconds, otherwise OSD (On Screen Display) will be automatically turned off. DIMMER 3 Press ENT to finish adjustments or wait 10 seconds until OSD disappears; the adjustment will be saved automatically. Front Panel Controls DIMMER Remote Control 1 2 Press and hold DIMMER for at least 2 seconds to show the VISUAL EQ OSD. To change VISUAL EQ, press DIMMER or press or to cycle through the OSD as FLAT, NIGHT MOVIE, SOFT, SHARP, HIGHT CONT, and FLAT. (Default: SHARP) VISUAL EQ mode (manufacturer's settings) selection (VISUAL EQ MODE) FLAT: Normal Setting (Visual EQ OFF) NIGHT MOVIE: Suitable for movies in which dark scenes frequently appear. SOFT: Suitable for CGs and animated films. SHARP: Suitable for old movies where images are not clearly shown. · "FLAT" will change to "CUSTOM", when any of the picture mode (Brightness, Color, Tint, Contrast and Sharpness) has been adjusted · NIGHT MOVIE, SOFT, SHARP and CONTRAST are fixed values. If the picture mode is changed, they automatically change to CUSTOM mode. · To return FLAT mode, press RESET on the picture mode, or change values of BRIGHT, COLOR, TINT, CONTRAST and SHARPNESS to 0 manually. 8-EN PKG-1000P_EN. indd EN8 5/17/2005 1:39:50 PM System Setup Operation IR transmitter, source names and Audio levels can be adjusted for all available sources. · Once this adjustment is made, all sources are affected. SELECT ENT AUDIO LEVEL 2 (Setting for Aux2): Press and to select HIGH/MID/LOW. (Default: HIGH) AUDIO LEVEL 3 (Setting for Aux3): Press and to select HIGH/MID/LOW. [. . . ] · When making connections to the car's electrical system, be aware of the factory installed components (e. g. Do not tap into these leads to provide power for this unit. When connecting the TMX-R1000P to the fuse box, make sure the fuse for the intended circuit of the TMX-R1000P has the appropriate amperage. Failure to do so may result in damage to the unit and/or the vehicle. [. . . ]