User manual ALPINE PXE-H650

[. . . ] ® PXE-H650 Audio Processor OWNER'S MANUAL WARNING It is dangerous and illegal for a driver to watch the Video/TV while driving any vehicle. The driver may be distracted from looking ahead and an accident could occur. Caution · Read this manual thoroughly before starting installation and operation. You will find a number of Safety Warnings in this manual to tell you about things that could hurt you or other people if you were to ignore the Warnings. We cannot be responsible for problems resulting from failure to observe the Warnings in this manual. [. . . ] Press the reset button after correcting any problems. Navigate to "RECALIBRATE MULTEQ" in the display. Press "DONE" on the remote control to finalize MultEQ filter calibration or "MEASURE" to the next mic position of calibration. The LED blinks slowly between position measurements. 3. 13 BASIC OPERATION 5. "MEASURE POS 2" Reposition the microphone to the secondary position in the vehicle. When ready, exit the vehicle and press "MEASURE" on the remote control to begin. The MultEQ LED illuminates a steady green. "CHK OUTPUTS & MIC" If the MultEQ LED is blinking fast, something may have happened to the mic during the user's exit. Make any necessary corrections to position, etc. It will then be necessary to restart the calibration sequence. At this point, press the reset button and navigate to the "RECALIBRATE MULTEQ" option screen. Press "ENTER" to select this option. The "2-WAY OUTPUT" screen is displayed. Configure this setting the same as previous MultEQ sequence. Press "ENTER" and re-check amp and crossover levels with Track 3 -Pink Noise. Press "ENTER" when ready to restart the MultEQ calibration sequence. Resume the first MIC position measurement (and speaker detection) by jumping back to step 3 when ready. Next MIC Position At the "MEASURE POS 3" display, reposition the microphone to another position. Repeat Step 5 above for this new position. Continue this process for up to 5 more microphone positions. 4 calibrated positions is the minimum for proper MultEQ response. 6 positions is recommended for optimal results. Normally, the more locations used, the more accurate the final EQ curve. [. . . ] Volume/Balance/Fader/Sub Level Source Select . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HU (Factory)/AUX Remote Turn-on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Automatic Input Signal Sensing Turn-off Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 minutes 21 SPECIFICATIONS SPECIFICATION MAIN UNIT MAIN Input AUX Input Max Input Level Max Input Level Max Input Level Output Impedance Frequency Response THD SNR GENERAL Power Requirement Operating Current Operating Temperature Dimensions Weight VALUE 16 Vrms 1. 5 Vrms (AUX PRIMARY OFF) 2. 5 Vrms (AUX PRIMARY ON) < 1k 20 Hz to 20 kHz < 0. 2% 82 dB 12. 0 VDC (11-16 VDC allowable) < 700 mA +14°F to +140°F -10°C to +60°C) 252mm x 38mm x 149mm 1. 0kg/35. 3 oz Accessories RUE-4265 Remote Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]